Mikado LOGO 200 Kurzanleitung

LOGO 200—Quick Start Guide
Congratulations on the purchase of your new Mikado LOGO 200!
To ensure the best experience for you, this model has been pre setup and test flown by Mikado Factory Team members.
Follow these few steps, and you will be flying in no time at all!
Step 1 —Update your Radio to the latest version
Since the LOGO 200 uses a special version of 6.4 software, you will need to make sure to update your VBC or VBCT ra­
dio to the latest version in order to have proper function, and access to the menu options which are specific for this heli.
So, please make sure you update your radio to the latest version before attempting to adjust parameters in the model.
Step 2 —Binding the model
We always recommend REMOVING THE MAIN BLADES, AND THE TAIL ROTOR PROPELLER, when doing initial
binding. Turn your VBC radio on, and
so your motor switch must be in OFF. Then, plug in the main battery to the helicopter. Wait approximately 10
seconds until the LED on the VBar NEO mini starts flashing
on your VBC radio and select on the LOGO 200 model. After this, the model is bound and ready for flight.
Step 3 - GO FLY!
The LOGO 200 comes set up with 3 preset flight banks/rpms. These flight modes range from "Mild to Wild". We hope
that you will be able to find a bank which suits your flying style.
Bank 1—
This bank is set up for very smooth flying and beginners. RPM is set to 3,800, with slow and stable flight
settings. This bank is great for right side up, and inverted, hovering and forward flight maneuvers. Also it is great for
indoor and outdoor flying. When flying indoors, mind a sensible safety distance to the model, to others, to obstacles.
Bank 2—
This bank is set up for sport flying and light 3D. RPM is set to 4,800, with medium and moderate flight settings.
This bank is great for sport flying, flips, and most smooth 3D maneuvers. We recommend this bank for outdoor flying
only, unless you are an accomplished pilot in which case it can be flown indoors as well.
Bank 3—
This bank is setup for aggressive 3D flying. RPM is set to 5,800 with fast and aggressive flight settings. This
bank is perfect for all aggressive 3D maneuvers. We recommend this bank for outdoor flying only.
TIPS FOR ADJUSTING FLIGHT SETTINGS
The LOGO 200 comes default with a special version of "Express" VBar NEO 6.4 software. There is limited adjustability in
this mode, as we do not want customers to preoccupy about, or accidentally set wrong values. Here are the adjustable
values.
Cyclic Adjustments
Center aggresiveness of
Expo
cyclic inputs
Agility Rotation rate of cyclic
Gyro Gain of cyclic
Gain
Adjusts the feel of cyclic
Style
Higher = Robotic
Lower = Vivid
Due to the size of the LOGO 200 and it's wide RPM range, and the separate tail motor (which makes the tail
authority independent of the main rotor rpm), some flight settings are very specific to the RPM of the main
rotor blades. We have tuned all settings to work optimally in each bank at their respective default RPMs.
The settings will work well around approximately +/– 500 RPM from the default value.
If you wish to adjust drastically the RPMs in each bank to you own style, we DO NOT RECOMMEND
adjusting only the RPM value more then +/– 500 RPM from the default value. This can cause some other "RPM
Specific Settings" to become not tuned properly, and will result in poor performance. If you wish to make such
changes, we highly recommend upgrading your VBar NEO mini to the Pro or Pro+Rescue Version.
RESTRICTED RPM RANGES—The LOGO 200 has a very wide RPM range of around
3,000–6,500 rpm. However, we have found there are certain RPM ranges in which the model
resonates, resulting in wobbles and poor performance. These RPM ranges are around
3950–4250 RPM and 4950–5250 RPM. We DO NOT RECOMMEND setting your RPM in these
specific ranges.
ENSURE THE MOTOR SWITCH IS SET TO
DEFAULT FLIGHT SETTINGS
Tail Adjustments
Expo
Yaw Rate
Gain
Governor Adjustment
Headspeed Main Rotor RPM
green and red. At this point you can click into the Bind option
Center aggresive­
ness of tail inputs
Rotation rate of tail
Gyro Gain of tail
OFF. In Idle the tail motor will turn on
All other values, even if visible, are
not changable on the LOGO 200
"Express" Software.
Changing them will have no actual
effect.
For unlimited adjustability, please
upgrade to the Pro or
Pro+Rescue Version of
software!
Manual