REVELL North American Rockwell 0V-10A BRONCO Bedienungsanleitung Seite 2

H-145-380
WING AND BOOM ASSFMBLY
tBOTTOM - W H I T E <
16
8 WING TOP
9 WltlG BOTTOM
10 LEFT BOOM INSIDE
11 LEFT BOOM OUTSIDE
12 LEFT EXHAUST PIPE
13 BIGHT BOOM INSIOE
14 RIGHT BOOM OUTSIDE
15 RIGHT EXHAUST PIPE
16 STABILIZER
L Cernent WING TOP ( 8 ) to BOTTOM ( 9 ) .
2. Cernent two halves of LEFT BOOM Parts
( 1 0 ) and ( 1 1 ) together. Cernent LEFT EX-
HAUST PIPE ( 1 2 ) t o OUTSIDE.
3. Cernent RIGHT BOOM Parts ( 1 3 ) and ( 1 4 )
together t h e n cernent RIGHT EXHAUST
PIPE ( 1 5 ) t o OUTSIDE.
4 . Cernent LEFT and RIGHT BOOMS t o WING
t r a p p i n g STABILIZER ( 1 6 ) between BOOMS
on assembly.
5. Cernent FUSELAGE f r o m STEP 1 t o WING.
GEAR AND ARMAMENT INSTALLATION
17
18
19
20
NOSE GEAR
WHEEL i Z Parts)
MAIN GEAR LEFT
MAIN GEAR RIGHT
22 DROP TANK RIGHT SIDE
23 BOMBS (4 Parts)
24 SIDEWINDER MISSILE (2 Parts)
25 MISSILE PYLONS (2 Parts)
21 DROP TANK LEFT SIDE 26 FUSELAGE SUPPORT STRUT (OpBonal)
Turn Mode! upside down as shown.
1. Cernent NOSE GEAR ( 1 7 ) to FUSELAGE.
2. Cernent a WHEEL ( 1 8 ) to each of the MAIN
GEARS LEFT ( 1 9 ) ànd RIGHT ( 2 0 ) . Cernent
G FARS to the BOOMS.
3.
Cernent the DROP TANK HALVES ( 2 1 ) and
( 2 2 ) together and t o FUSELAGE.
4 . Cernent the four BOMBS ( 2 3 ) to FUSE-
LAGE.
5. Cernent the two SIDEWINDER MISSILES
( 2 4 ) to the MISSILE PYLONS ( 2 5 ) then
cernent assemblies t o WING.
6. Install the FUSELAGE SUPPORT STRUT
( 2 6 ) if you wish.
PROPELLER SHAFT (2 Parts)
ENGINE COWLING (2 Parts)
LEFT PROPELLER
RIGHT PROPELLER
WINDSHIELD & CANOPY (Çlear)
LEFT CANOPY SIDE (Clesr)
RIGHT CANOPY SIDE (Clear)
ELEVATOR BALANCE WEIGHTS (2 Parts)
4.
5.
Turn model right side up.
PLACE, DO NOT CEMENT A PROPELLER
SHAFT ( 2 7 ) in each ENGINE COWLING
( 2 8 ) . Then PRESS, DO NOT CEMENT THE
LEFT PROPELLER ( 2 9 ) on a PROPELLER
SHAFT. Cernent the assembly t o t h e LEFT
BOOM.
PRESS, DO NOT CEMENT THE RIGHT
PROPELLER ( 3 0 ) on a PROPELLER SHAFT
and cernent assembly t o the RIGHT BOOM.
Cernent the WINDSHIELD and CANOPY
TOP ( 3 1 ) to FUSELAGE. Then cernent the
LEFT ( 3 2 ) and RIGHT ( 3 3 ) CANOPY SIDES
in position.
Cernent two ELEVATOR BALANCE WEIGHTS
( 3 4 ) to the ELEVATOR.
Install DECALS following instructions on
back of DECAL SHEET.