Operation - Renkforce 2142906 Bedienungsanleitung

Operating instructions
Bluetooth Music Receiver
Item no. 2142906
Intended use
The music receiver is designed to receive wireless audio signals (voice or music) from mobile
phones, tablets, laptops and other devices that have an appropriate Bluetooth connection. The
device has a transmission range of up to 20 metres when there are no obstructions.
The audio signal can be picked up on the receiver through the 3.5 mm audio input. Power is
supplied via the included 5 V/DC adaptor.
The A2DP Bluetooth protocol and the SBC codec must be supported in order to transmit music.
Bluetooth is a technology which is used to transmit data wirelessly over short distances.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Music receiver
• Micro USB power adaptor
• 3.5 mm male to male audio cable (185 cm)
• 3.5 mm female to RL audio cable (17 cm)
• Operating instructions
Up-to-date operating instructions
To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR
code on this page. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Do not place the music receiver near to sources of heat.
• Do not listen to excessively loud music over an extended period of time. This may
damage your hearing.
• Only power the device using the included adaptor.
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Power Adaptor
• Connect the appliance to a wall socket that can be accessed easily.
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public
supply. Before plugging in the power adaptor, check whether the voltage stated on
the power adaptor complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during
storms.
Operating elements
1
2 3

Operation

1. Connect your audio playback device (speakers, amplifier etc.) to the AUDIO OUT (2) socket
on the music receiver using the included cable. Connect the included RL audio adapter if
the connection takes place through RCA sockets.
2. Ensure that you place the product in a secure location.
3. Connect one end of included power adaptor to the DC 5V (3) input, and the other end to
a power outlet.
4. The LED (1) on the music receiver will flash once every 5 seconds. This indicates that the
receiver is searching for Bluetooth-capable devices.
a) Establishing the Bluetooth connection
1. Now activate the Bluetooth function on the device that you want to use to transfer audio
data to the music receiver. For example, on an Android smartphone you will find the function
in 'Connections' in the settings. In Apple iOS, you will find the function under Bluetooth
settings. Look up the details in the instruction manuals of the devices concerned.
2. Enter the PIN code for a connection. Use 0000 if necessary. Some devices do not require a
PIN code. The music receiver can save up to a maximum of 8 devices.
3. Once the device is displayed as "Music Receiver", tap on it to pair your device (e.g. your
smartphone) with the music receiver. If no other devices are connected to the music
receiver, this device will automatically be selected for audio playback.
4. The LED (1) flashes once every 5 seconds during the pairing process. The LED (1) stays
on once a connection has been successfully established.
b) Playback
1. You can play back an audio file on your device. The audio signal is automatically transmitted
to the Bluetooth receiver. Depending on the device, it is also possible to switch the output
between the Bluetooth receiver and the device that you are using the play the files.
2. It is also possible to play a video. The picture will be displayed on your device (e.g. tablet)
while the sound will be played on the audio device that is connected to the music receiver.
3. Use your smartphone or tablet to control the playback and the volume.
c) Disconnecting the Bluetooth connection.
• To disconnect your device from the music receiver, navigate to the Bluetooth settings again
and terminate the connection. Alternatively, you can simply turn off the Bluetooth function.
Multiple devices may be paired with the music receiver via the Bluetooth function,
but only one of them can be used to play back audio. If you want to use another
device as the signal source, the current device must first be disabled.
1 LED
2 AUDIO OUT
3 DC 5V