Navigating Through The Main Menu - Mitsubishi Electric Mr.SLIM PKA-M KA Serie Bedienungshandbuch

3. Operation
3.4. Fan speed setting
Room
Cool Set temp.
Mode Temp.
F1 F2
Press the [F4] button to go through the fan speeds in the following order.
Auto
• The available fan speeds depend on the models of connected indoor
units.
Note:
The number of available fan speeds depends on the type of unit
connected. Note also that some units do not provide an "Auto" setting.
In the following cases, the actual fan speed generated by the unit will differ
from the speed shown the remote controller display.
1. While the display is showing "STAND BY" or "DEFROST".
2. When the temperature of the heat exchanger is low in the heat mode.
(e.g. immediately after heat operation starts)
3. In HEAT mode, when room temperature is higher than the temperature
setting.
4. In COOL mode, when room temperature is lower than the temperature
setting.
5. When the unit is in DRY mode.
■ Automatic fan speed setting (For wireless remote controller)
It is necessary to set for wireless remote controller only when automatic
fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic fan
speed at default setting.
1 Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted A
2 Press the AUTO STOP
blinks and setting No. is lighted B
(Setting No.01: without automatic fan speed)
3 Press the temp.
(Setting No.02: with automatic fan speed)
If you mistook the operation, press the ON/OFF
again from procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
Downloaded from www.Manualslib.com
Fri
Auto
Fan
F3 F4
.
button.
.
buttons to set the setting No.02.
B
MODEL SELECT
A
ON/OFF TEMP
3
FAN AUTO STOP
2
MODE VANE AUTO START
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
14
manuals search engine
3.5. Airflow direction setting
3.5.1 Navigating through the Main menu
<Accessing the Main menu>
Main
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
F1
<Item selection>
Main
Vane·Louver·Vent. (Lossnay)
High power
Cursor
Timer
Weekly timer
OU silent mode
Main display:
F1
<Navigating through the pages>
Main
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor
F1
<Saving the settings>
Mon Tue Wed Thu Fri Sat Sun
Start
button and operate
Setting display:
day
F1
<Exiting the Main menu screen>
Cool
Mode
F1
Press the [MENU] button.
Main menu
The Main menu will appear.
Cursor Page
F2 F3 F4
Press [F1] to move the cursor down.
Main menu
Press [F2] to move the cursor up.
Cursor Page
F2 F3 F4
page
Main menu
Press [F3] to go to the previous
page.
Press [F4] to go to the next page.
Page
F2 F3 F4
Select the desired item, and press
OU silent mode
the [SELECT] button.
Stop Silent
-
The screen to set the selected item
will appear.
F2 F3 F4
Press the [RETURN] button to exit
Fri
the Main menu and return to the
Main display.
Room
Set temp. Auto
If no buttons are touched for
10 minutes, the screen will
Temp. Fan
automatically return to the Main
display. Any settings that have not
been saved will be lost.
F2 F3 F4
7