Migatronic RALLY MIG 161i Handbuch Seite 3

RALLY MIG 161i - Factory setting
Setting possibilities
Primary parameters:
1 Welding current Area depends on
Wire feed speed
Thickness of material
2 Arc length
Secondary parameters:
1 Arc power (MMA)
3 Hotstart (MMA)
TIG process (TIG)
1 Arc Adjust (MIG)
6 Burnback (MIG)
MIG parameters
Set welding current (A)
Burnback
Arc adjust (electronic choke)
1
Downloaded from www.Manualslib.com
Area Step Factory setting
2T
1 Depending on
program program
0.1
0.1
-9.9 – +9.9 0.1 0.0
0 - 150 1 25
0 - 100 1 25
ON/OFF OFF
-5.0 – +5.0 0.1 0.0
1 – 30 1 5
MMA parameters
Arc
power
Hotstart
Short circuit
Set welding
current (A)
manuals search engine
QUICKGUIDE RALLY MIG 161i
Programs
No.
Unit
P106
P101
P109
A P102
P116
m/min
P111
mm
P119
V
P112
P201
%
P209
P202
%
P311
P319
-
P312
ms
P359
P352
P369
P372
P501
TIG
welding
P509
P502
P561
P569
P562
Note: Fe programs with reversed polarity are recommended
501 3775 E
Wire Material
Ø 0.6 mm Fe SG2
Ø 0.8 mm Fe SG2
Ø 0.9 mm Fe SG2
Ø 1.0 mm Fe SG2
Ø 0.6 mm Fe SG2
Ø 0.8 mm Fe SG2
Ø 0.9 mm Fe SG2
Ø 1.0 mm Fe SG2
Ø 0.8 mm CrNi ER 316 LSI
Ø 0.9 mm CrNi ER 316 LSI
Ø 1.0 mm CrNi ER 316 LSI
Ø 0.8 mm AlMg5 ER5356
Ø 0.9 mm AlMg5 ER5356
Ø 1.0 mm AlMg ER5356/ER5554
Ø 0.9 mm AlSi5 ER4043
Ø 1.0 mm AlSi5 ER4043
Ø 0.9 mm AlMg3Mn ER5554
Ø 1.0 mm AlSi12 ER4047
Ø 0.8 mm CuAl8 Brazing
Ø 0.9 mm CuAl8 Brazing
Ø 1.0 mm CuAl8 Brazing
Ø 0.8 mm CuSi3 Brazing
Ø 0.9 mm CuSi3 Brazing
Ø 1.0 mm CuSi3 Brazing
for Innershield wires
UK
Gas
CO
2
CO
2
CO
2
CO
2
ArCO (82/18)
2
ArCO (82/18)
2
ArCO (82/18)
2
ArCO (82/18)
2
ArCO (98/2)
2
ArCO (98/2)
2
ArCO (98/2)
2
Ar
Ar
Ar (100)
Ar (100)
Ar
Ar (100)
Ar (100)
ArCO (98/2)
2
ArCO (98/2)
2
ArCO (98/2)
2
ArCO (98/2)
2
Ar (100)
ArCO (98/2)
2