Technical Data; Safety Instructions - Felisatti R16/750 Bedienungsanleitung

Original instructions

TECHNICAL DATA

Router
Input power
No-load speed
Clip diameter
Approx. weight (without acces.)
Read the operating instructions
Protection category II power tool; double
insulated
In accordance with essential applicable
safety standards of European directives
In accordance with essential applicable
safety standards of Russian Federation
Wear eye protection
Wear ear protection
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
C Start-up switch (Fig.1)
D Clamping nut (Fig.1)
EQUIPMENT
- Clip, ∅ 8 mm
- Fixed spanner 13 mm
- Fixed spanner 17 mm
- 1 cutting base (FT1020 Fig.4)
- 1 copying base (FT1050 Fig.5)
- 1 guide bushing 10 mm
- 1 guide bushing 12 mm
- Operating instructions

- Safety instructions

- Warranty
SAFETY INSTRUCTIONS
• See "Safety Instructions" manual, supplied with this
instruction manual.
• WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company's safety instructions
regarding the responsibility of employees.
• For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
low-voltage wiring sitemaps.
• Do not pierce the motor housing as this could damage
the double insulation (use adhesive labels).
W
rpm
mm
kg
• Always unplug the machine before carrying out
work on it.
• Always stop the machine by switching it off, not by
unplugging it.
• WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre.
• Always keep the mains lead clear of the working range
of the machine.
• Only plug the machine in when it is switched off.
• Hold the machine firmly in both hands and in a stable
position.
• When working with the machine, always wear safety
goggles and ear protection. Other personal protec-
tion equipment such as dust masks, gloves, helmet
and apron should be worn when necessary, along
with non-slip safety footwear. A dust mask is required
when the dust from the material deburred, such as
paint or other coating, is harmful. If in doubt, use
safety equipment.
• Make sure the vents are free when working with
dust. If they require cleaning, first unplug the ma-
chine, do not use metal objects and avoid damag-
ing internal parts.
• Do not allow the machine to get wet, nor should it be
used in wet environments.
• Check for correct piece fixing before commencing any
operation.
• Only milling heads with acceptable revolutions that are
at least the same as the maximum off-load revolutions
of the machine should be used.
• The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
• It should be ensured that the milling head is firmly held
in place before the machine is operated.
• The milling head should only be brought into contact
with the work-piece after it has been switched on.
• Hold the machine firmly in both hands and in a stable
position.
• The milling machine must never be used on metal
objects, such as nails and screws.
• Hand must be kept clear of the milling machine while it
is operating.
• The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
• The operator should remain alert and keep the milling
head apart from all objects during operation.
• The motor must be allowed to come to completely stop
before being put to one side between uses.
• The milling heads should not be touched after use
because they could cause serious burns.
R16/750
750
27000
8
1.9