Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - Maestro MID 1000 E Originalbetriebsanleitung

GB
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch off:
Press the ON/OFF switch (5) briefly.
Ÿ
6.2 Adjusting the speed (Fig. 6/Item 5)
Ÿ
You can infinitely vary the speed whilst using the
tool.
Ÿ
Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (5).
Ÿ
Select the correct speed: The most suitable speed
depends on the workpiece, the type of use and the
drill bit used.
Ÿ
Low pressure on the ON/OFF switch (5): Lower
speed (suitable for: small screws and soft
materials)
Ÿ
Greater pressure on the ON/OFF switch (5):
Ÿ
Higher speed (suitable for large/long screws and
hard materials)
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
Ÿ
The drill bit is easier to control when starting the
hole and will not slide away.
Ÿ
You avoid drilling messy holes (for example in tiles).
6.3 Preselecting the speed (Fig. 6/Item 6)
Ÿ
The speed setting ring (6) enables you to define the
maximum speed. The ON/OFF switch (5) can only
be pressed to the defined maximum speed setting.
Ÿ
Set the speed using the setting ring (6) on the
ON/OFF switch (5).
Ÿ
Do not attempt to make this setting whilst the drill is
in use.
6.4 Clockwise/Counter-clockwise switch
(Fig. 6/Item 7)
ŸChange switch position only when the drill is at a
standstill!
ŸSwitch the direction of the hammer drill using the
clockwise/counter-clockwise switch (7):
Direction Switch position
Clockwise (forwards and drill) R
Counter-clockwise (reverse) L
6.5 Drill / hammer drill selector switch
(Fig. 7/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
8
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the hammer
drill position. (Position B)
Use for: Concrete, rock, masonry
6.6 Tips for working with your hammer drill
6.6.1 Drilling concrete and masonry
Ÿ
Switch the Drill/Hammer drill selector switch (3) to
position B (Hammer drill).
Ÿ
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
6.6.2 Drilling steel
Ÿ
Switch the drill / hammer drill selector switch (3) to
position A (drill).
Ÿ
Always use HSS drill bits (HSS = high speed steel)
and a low speed setting for drilling steel.
Ÿ
We recommend that you lubricate the hole with a
suitable cutting fluid to prevent unnecessary drill bit
wear.
6.6.3 Inserting/Removing screws
Ÿ
Switch the Drill/Hammer drill selector switch (3) to
position A (drill).
Ÿ
Use a low speed setting
6.6.4 Starting holes
If you wish to drill a deep hole in a hard material
(such as steel), we recommend that you start the
hole with a smaller drill bit.
6.6.5 Drilling tiles
Ÿ
To start the hole, switch the drill / hammer drill
selector switch (3) to position A (drill).
Ÿ
Switch the drill / hammer drill selector switch (3) to
position B (hammer drill) as soon as the drill bit has
passed through the tiles.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its aftersales
service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Ÿ
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe