Before Starting The Equipment; Operation - Maestro MID 1000 E Originalbetriebsanleitung

Additional information for electric power tools
mWarning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Ÿ
Only use appliances which are in perfect working
order.
Ÿ
Service and clean the appliance regularly.
Ÿ
Adapt your working style to suit the appliance.
Ÿ
Do not overload the appliance.
Ÿ
Have the appliance serviced whenever necessary.
Ÿ
Switch the appliance off when it is not in use.
Ÿ
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust
is used.
2. Damage to hearing if no suitable ear protection
used.
3. Health damage caused by hand-arm vibrations
the equipment is used over a prolonged period
is not properly guided and maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1. Fitting the additional handle (Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
use the tool without the additional handle.
The additional handle (8) is secured to the hammer
drill by a clamp. During the handle clockwise tightens
this clamp. Turning it anti-clockwise will release the
clamp.
Ÿ
The supplied additional handle (8) must first be
fitted. To do this, the clamp must be opened by
turning the handle until it is wide enough for the
additional handle to be slid over the chuck (1) and
on to the hammer drill.
Ÿ
After you have positioned the additional handle (8),
turn it to the most comfortable working position for
you.
Ÿ
Now turn the handle in the opposite direction again
until the additional handle is secure.
Ÿ
The additional handle (8) is suitable for both
lefthanded and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
The depth stop (2) is held in place by the additional
handle (8) by clamping. The clamp can be released
and tightened by turning the handle.
Ÿ
Release the clamp and fit the depth stop (2) in the
recess provided for it in the additional handle.
Ÿ
Set the depth stop (2) to the same level as the drill
bit.
Ÿ
Pull the depth stop back by the required drilling
depth.
Ÿ
Turn the handle on the additional handle (8) until it
is secure.
Ÿ
Now drill the hole until the depth stop (2) touches
the workpiece.
5.3 Fitting the drill bit (Fig. 5)
Ÿ
Always pull the power plug before making
adjustments to the equipment.
Ÿ
Release the depth stop (2) as described in 5.2 and
push it towards the drill handle. This provides free
access to the chuck (1).
Ÿ
Undo the chuck by turning it anti-clockwise with the
supplied chuck key (9).
Ÿ
To ensure that it is perfectly positioned the drill bit
or tool should be inserted as far as possible into the
chuck. After inserting the drill bit or tool, tighten the
chuck (1) by turning the chuck key (9) clockwise
until the drill bit or tool is secure. Check that the drill
bit is secure in the chuck (1).
Ÿ
Check at regular intervals that the drill bit or tool is
secure (pull the mains plug).

6. Operation

6.1 ON/OFF switch (Fig. 6/Item 5)
Ÿ
First fit a suitable drill bit into the tool (see 5.3).
Ÿ
Connect the mains plug to a suitable socket.
Ÿ
Position the drill in the position you wish to drill.
To switch on:
Press the ON/OFF switch (5)
GB
7