Before Starting The Equipment; Operation - Maestro MCD 182 Originalbetriebsanleitung

GB
Keep the noise emissions and vibrations to a
Ÿ
minimum.
Ÿ
Only use appliances which are in perfect working
order.
Ÿ
Service and clean the appliance regularly.
Ÿ
Adapt your working style to suit the appliance.
Ÿ
Do not overload the appliance.
Ÿ
Have the appliance serviced whenever necessary.
Ÿ
Switch the appliance off when it is not in use.
Ÿ
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust
is used.
2. Damage to hearing if no suitable ear protection
used.
3. Health damage caused by hand-arm vibrations
the equipment is used over a prolonged period
is not properly guided and maintained.

5. Before starting the equipment

Be sure to read the following information before you
use your cordless screwdriver for the first time:
1. Charge the battery pack only with the charger
supplied.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing
in walls.

6. Operation

6.1 Charging the battery pack (Fig. 2/3)
1. Take the rechargeable battery pack out of the
handle (Fig. 2), pressing the pushlock buttons at
the side to do so.
2. Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the socket.
3. Plug the battery pack into the charging adapter.
The LED (a) will come on to indicate that the
battery pack is being charged. The temperature
of the battery pack may rise slightly during the
charging operation. This is normal.
Important! The battery charger does not
switch off automatically when the battery is
fully charged.
6
If the battery pack fails to become charged, please
check
Ÿ
whether there is voltage at the socket-outlet
Ÿ
whether there is proper contact at the charging
contacts on the charger.
If the battery still fails to become charged, please
return
Ÿ
the charger
Ÿ
the battery pack
to our Customer Service Department.
To ensure that the battery pack provides long service,
you should take care to recharge it promptly. You
must recharge the battery pack when you notice that
the power of the cordless screwdriver drops.
Never fully discharge the battery pack. This will cause
it to develop a defect!
6.2 Torque setting (Fig. 4 / Item 1)
The cordless screwdriver is fitted with a mechanical
torque selector.
The torque for a specific size of screw is selected
with the set-collar (1). The correct torque depends on
several factors:
Ÿ
on the type and hardness of material in question
Ÿ
on the type and length screws used
Ÿ
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
6.3 Drilling (Fig. 4 / Item 1)
For drilling purposes, move the set-collar to the last
step „Drill". In this setting the slip clutch is inactive.
The maximum torque is available in drilling mode.
6.4 Forward/Reverse switch (Fig. 5 / Item 3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the
batterypowered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To avoid
causing damage to the gearing it is advisable to
change the direction of rotation only when the tool is
at a standstill. The On/Off switch is blocked when the
slide switch is in centre position.
6.5 On/Off switch (Fig. 5 / Item 4)
Infinitely variable speed control is possible with the
On/Off switch. The further you press the switch, the
higher the speed of the battery-powered
drill/screwdriver.