Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Product overview
#
Mouse mode
1
Left mouse button
2
Mouse/presenter switch
3
Button off
4
Button off
5
Button off
6
Laser outlet
7
Right mouse button
8
Scroll wheel
Button
; activate laser
9
10
Button off
11
On/off switch
12
Mouse sensor
13
Battery compartment; also storage option for USB receiver
Inserting/replacing the batteries
• Remove the battery compartment cover on the underside by sliding it out backward.
• Insert 2 AAA/Micro batteries. Pay attention to the polarity markings inside the battery com-
partment.
• Close the battery compartment again.
A battery change is required when a LED on the scroll wheel flashes, the range
decreases sharply or the product stops working after being switched on.
Connecting the USB receiver
• Remove the USB receiver from the battery compartment on the underside of the mouse.
For transport or storage purposes, the USB receiver can be inserted into the cor-
responding opening in the battery compartment so that you do not lose it.
• Connect the USB receiver to a free USB port on your computer. The computer does not need
to be switched off. The operating system will recognise the mouse as new hardware and
install the necessary drivers (these are included in the operating system).
Presenter mode
Decrease the volume
Mouse/presenter switch
Button
; start presentation
Button
; page back
("Image " / "PgUp" keyboard function)
Button
; turn the presentation dark
(show a black page)
Laser outlet
Increase the volume
Cancel presentation ("ESC" keyboard function)
Button
; activate laser
Button
; page forward
("Image " / "PgDn" keyboard function)
On/off switch
Button off
Operation
a) General information
• The product is equipped with a class 2 laser. Laser signs in different languages are included
in the package. If the sign on your mouse is not written in your local language, please attach
the corresponding sign to your mouse.
• Use the slide switch (11) on the underside of the mouse to switch it on ("ON") or off ("OFF").
When switched on, the LED on the scroll wheel lights up briefly.
• If the mouse is switched on and it is not used, the standby mode will be activated after ap-
prox. 20 seconds of inactivity to save power.
• After about 8 minutes of inactivity, the sleep mode will be activated. To reactivate the mouse,
press the left or right mouse button.
• If you are not going to use the mouse for a long time (for example, during transport or ex-
tended work breaks), switch off the mouse using the on/off switch on the underside ("OFF"
switch position = switched off) to save power and increase the battery life.
b) Mouse
• Place the mouse on a smooth, flat, sufficiently large surface.
The mouse's optical motion sensor does not work on all surfaces. Especially on
reflective surfaces or glass, the function may be limited. If the cursor does not move,
try placing the mouse on a suitable mouse pad.
• Briefly press the button on the left (2) to toggle between mouse mode and presenter mode.
• If the cursor doesn't move properly after you have used the mouse for a long period of time,
check whether the sensor on the bottom of the mouse is dirty. Clean it by blowing briefly on
the sensor or using a soft, clean brush.
• If the cursor in the operating system (for example, Windows) is moving too slow or too fast,
use your operating system's settings to configure the cursor speed.
c) Presenter
• Briefly press the button on the left (2) to toggle between mouse mode and presenter mode. In
presenter mode, 5 button icons ( ,
The functions available in presenter mode can be found in the table in section "Prod-
uct overview".
• Start the presentation software and load the desired presentation.
Caution!
When the laser button (9) is pressed, the laser beam exits the laser outlet (6).
Care and cleaning
• The product is maintenance-free for you, apart from the occasional battery replacement. Un-
der no circumstances should you service any of the components in the interior of the product.
• Switch off the mouse before each cleaning (set the slide switch on the underside to the
"OFF" position).
• Use a dry, lint-free cloth to clean the product.
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solu-
tions as they can cause damage to the housing and malfunctioning.
Disposal
a) Product
Electronic devices are recyclable waste and must not be placed in household waste.
At the end of its service life, dispose of the product according to the relevant statu-
tory regulations.
Remove any inserted batteries and dispose of them separately from the product.
b) Batterien & rechargeable batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/re-
chargeable batteries. Disposing of them in the household waste is prohibited.
Batteries containing hazardous substances are labelled with this symbol to indicate
that disposal in household waste is forbidden. The abbreviations for heavy metals
in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable)
batteries, e.g. below the trash icon on the left).
Used batteries can be returned to local collection points, our stores or battery retailers.
You thus fulfil your statutory obligations and contribute to environmental protection.
, ,
and
) are backlit on the top of the mouse.
Werbung
Inhaltsverzeichnis
