Technical Data; Items Supplied - EINHELL PS 12 Betriebsanleitung

Anleitung PS 12 - Niro
Read the safety and operating instruc-
tions carefully before you use your
heater for the first time. Material and
features have been selected to rule out
malfunctions provided the heater is
used as intended. Check that all parts
are complete. Caution: Use only
outdoors or in well-ventilated areas!
1. Description
The party heater is used outdoors to heat nearby
areas. A burner inside the perforated plate body
produces the necessary heat, which is radiated to
the immediate surroundings by an aluminium
reflector as well as by the perforated plate itself.
The party heater has to be set up on a level,
incombustible surface with no - or only a very slight -
gradient. Its center of gravity can be lowered
considerably by filling sand in the foot.
To make it easier to change the gas bottle, the body
can be raised and locked in place on the appliance
itself.
The party heater is designed to work only with
propane-butane (liquefied gas). It is connected
directly to the gas bottle by means of a DVGW-tested
and approved hose pipe and a liquefied gas
regulator (outlet pressure 28-30/37 mbar, capacity
1,5 kg/h). The following regulations have to
be observed and adhered to when making the
connection:
Technical regulations concerning liquefied gas
(e.g. TRF)
Guidelines published by liability insurance
associations concerning the use of liquefied gas
in special applications

2. Technical data

Dimensions Overall height:
Reflector diameter:
Power rating:
Consumption: approx. 0,85 kg/h
Fuel: Propane/butane liquefied gas
Ignition: Piezo igniter
Monitoring: Thermoelectric flame monitor
Gas supply Gas bottles up to 11 kg
22.04.2004 12:47 Uhr

3. Items supplied

3.1 PS 12
Item 1 reflector
Item 2 burner assembly
Item 3 center pipe
Item 4 container lid
Item 5 container enclosure
Item 6 leg
Item 7 bulkhead
Item 8 washer, 6.4 mm dia.
Item 9 washer, 5.3 mm dia.
Item 10 hex nut M5
Item 11 hex nut M6
Item 12 screw M6x12 mm
Item 13 screw M5x12 mm
Item 14 hose clamp 12-20
Item 15 wheel set
3.2 PS 12 Niro
Item 1 reflector
Item 2 burner assembly
Item 3 center pipe, complete
Item 4 container lid
Item 5 container enclosure
Item 6 leg
Item 7 bulkhead
Item 8 washer, 6.4 mm dia.
Item 9 washer, 5.3 mm dia.
Item 10 hex nut M5
Item 11 edge protector, 360 mm long
Item 12 screw M6x12 mm
Item 13 screw M5x12 mm
Item 14 edge protector, 250 mm long
Item 15 adapter 1
Item 16 adapter 2
Item 17 hex nut M36
Item 18 hose clamp 12-20 mm
Item 19 wheel set
You will need the following additional tools for the
installation:
1 wrench 2 x SW 8 + 2 x SW 10 –
1 Phillips screwdriver
2300 mm
780 mm
4. Assembly (Fig. 1)
12 kW
Important: The item numbers in the text refer to the
item numbers in sections 3.1 or 3.2
4.1 PS 12
1. (Detail A) Attach the container enclosure (5) to
the leg (6) using four screws (13), washers (9)
and hex nuts.
Seite 7
GB
1 each
1 each
1 each
1 each
1 each
1 each
1 each
12 each
16 each
8 each
3 each
9 each
8 each
1 each
1 bag
1 each
1 each
1 each
1 each
1 each
1 each
1 each
12 each
16 each
8 each
1 each
12 each
8 each
3 each
1 each
1 each
1 each
1 each
1 bag
7