Inhaltsverzeichnis
Werbung
or knowledge if they have been supervised or instructed in
the safe operation of the fine-spray system and understand
the associated dangers. Otherwise, there is a danger of
operating errors and injuries.
Children must not be allowed to clean and perform
●
maintenance on the fine-spray system without supervision.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut
ASSEMBLY & DISASSEMBLY (fig 2, fig 3 and fig4)
Before any work on the machine itself, pull the mains
plug.
Assemble the spray gun head
Align the head and body, then rotate the machine body
clockwise. After the SDS lock knob locked, it is means secured
assembled already. See fig.2.
OPERATION
Preparing for Operation
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment area
is not permitted.
When purchasing paint, varnish and spray material, pay
attention to their environmental compatibility.
Preparing the Spray Surface
Note: Cover off the vicinity of the spray surface thoroughly and
generously.
The spray mist contaminates the environment. When spraying
in enclosures, surfaces not covered can become contaminated.
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding dust.
Suitable spray materials and recommended diluting agents
When diluting, pay attention that the spray material and
●
the diluting agent correspond. When using a faulty diluting
agent, lumps can develop that can lead to clogging of the spray
gun.
Determine the viscosity of spray materials
This spray gun used for max viscosity of spray material is 80
DIN. So you need to determine the material viscosity by DIN
cup. If viscosity is too high, it need to dilute the material at first.
To determin the DIN value, do the steps as belows:
1. Begin with material and cup at room temperature.
2. Submerge the cup into the material.(alternately you may
cover the drain hole with your finger and fill the cup with the
material).
3. Quickly raise the cup (or remove your finger) and begin
timing.
4. Stop timing when the steady stream first breaks at about 1 or
2 inches below the drain hole.
Filling the spray material
– Unscrew the spray material tank from the spray gun.
– Fill the spray material into the tank and screw the tank
off and an appropriate plug fitted in its place by an
authorized customer service agent. The replacement
plug should have the same fuse rating as the original
plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted into
a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual
current device (RCD) with a rated residual current of 30
mA or less.
Disassemble the spray gun head
Slide the SDS lock knob and then rotate the machine
body anti-clockwise, then pull out. See fig. 3.
Mounting the spray material tank
Screw the spray material tank onto the spray head and
fasten it claockwise.
firmly to the spray gun.
Starting Operation
Observe correct mains voltage! The voltage of the
●
power source must agree with the voltage specified
on the nameplate of the machine. Power tools
marked with 230 V can also be operated with 220 V.
●
Pay attention that the power tool cannot draw in
dust or other contamination during operation.
Switching On
To save energy, only switch the fine-spray system on
when you are using it.
– Plug the mains plug into a socket outlet.
– Grasp the power tool and point it at the spray surface.
The power tool is equipped with a two-step trigger
switch 9.
The first step s tarts the turbine. The second step
transports the spraying material.
– Pull the trigger switch 9 until spraying material starts to
come out.
Switching Off
– Release the trigger switch 9.
– Pull the mains plug from the socket outlet.
Adjusting the Spraying Capacity (see figure 5)
– To adjust the requested spraying capacity, turn the
thumbwheel 8:
–: Min. spraying capacity,
+: Max. spraying capacity.
Working Advice
Spraying (see figures 6–7)
Note: Observe the wind direction when operating the
power tool outdoors.
– Firstly, carry out a test-spray run and adjust the spray
pattern and the spray material quantity according to the
spray material. (For adjustments, see the following
sections)
– Be absolutely sure to hold the spray gun at a
consistent distance of 5 –15 cm perpendicular to the
spray object.
– Begin the spraying procedure outside the target area.
– Move the spray gun evenly cross -wise or up-and-
6
Werbung
Inhaltsverzeichnis
