Operation; Height Adjustment - Gemini UNX-7 Bedienungsanleitung

I n t r o d u c t i o n I n t r o d u c t i o n I n t r o d u c t i o n
I n t r o d u c t i o n I n t r o d u c t i o n
Congratulations on purchasing the Gemini UMX-7 VCA mixer. This state
of the art mixer is backed by a three year warranty, excluding crossfader
and channel slides. Prior to use, we suggest that you carefully read all the
instructions.
With VCA technology, audio is processed in a voltage-controlled amplifier
(VCA) removing it from the crossfader and channel slides giving them
extended life and reducing travel noise. The crossfader and channel slides
regulate the DC voltage that controls the VCA circuit. Additional
advantages of VCA technology include the ability to provide precise curve
adjustments for the crossfader and channel slides without sacrificing audio
quality. For additional information, refer to the diagrams on Page 3 for
crossfader adjustment and channel slide curve.
Features Features Features
Features Features
• 2 Stereo Channels
• State of the Art Cue Section with Split
• 3 Phono/Line Convertible, 1 Line, and 1 Mic Input
• Adjustable Input Assign Switches
• Channel Slide Curve Control
• Crossfader with Curve Control
• Crossfader Reverse (Hamster) Switch
• Cut Feature for Low, Mid and High for each channel
• Gain, High, Mid and Low tone controls for each channel
• Mic loop
• Talkover
• Balanced and Unbalanced Master Outputs
• Zone and Record outputs
• Dual mode display
Cautions Cautions Cautions
Cautions Cautions
1 . All operating instructions should be read before using this equipment.
2 . To reduce the risk of electrical shock, do not open the unit. There are
NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a
qualified service technician.
In the U.S.A., if you have any problems with this unit, call In the U.S.A., if you have any problems with this unit, call In the U.S.A., if you have any problems with this unit, call In the U.S.A., if you have any problems with this unit, call In the U.S.A., if you have any problems with this unit, call
1-732-969-9000 for customer service. Do not return equipment 1-732-969-9000 for customer service. Do not return equipment 1-732-969-9000 for customer service. Do not return equipment 1-732-969-9000 for customer service. Do not return equipment 1-732-738-9003 1-732-969-9000 for customer service. Do not return equipment
to your dealer. to your dealer.
to your dealer. to your dealer. to your dealer.
3 . Do not expose this unit to direct sunlight or to a heat source such as a
radiator or stove.
4 . This unit should be cleaned only with a damp cloth. Avoid solvents or
other cleaning detergents.
5 . When moving this equipment, it should be placed in its original carton
and packaging. This will reduce the risk of damage during transit.
6 . DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7 . DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES.

Height Adjustment

Height Adjustment Height Adjustment Height Adjustment Height Adjustment
When using a UMX mixer with professional turntables, such
as the Gemini PT Series, you can make the mixer level with
the turntable by removing the mixer's feet.
1 . Place a small screw driver under the foot's center anchor.
2 . Gently pry the center anchor up and the foot will come off.
Downloaded from www.Manualslib.com manuals search engine
To replace the foot:
1 . Place the foot on the mixer without the center anchor.
2 . Replace the center anchor and push down on it to anchor the foot to
the mixer.
Connections Connections Connections Connections Connections
1 . Make sure that the POWER (1) POWER (1) switch is in the off position. This unit POWER (1) POWER (1) POWER (1)
comes supplied with a 18 volt AC adaptor. Plug the adaptor into the
rear panel power jack. Then plug the adaptor into a proper power
source.
2 . The UMX-7 is supplied with 4 sets of output jacks. The BALANCED
MASTER OUTPUT (4) jacks are used to connect to your main MASTER OUTPUT (4) MASTER OUTPUT (4) MASTER OUTPUT (4) MASTER OUTPUT (4)
amplifier using standard cables with 1/4" connectors. We recommend
using the balanced amp outputs if the cables to your amp are 25 feet or
more. BALANCED MASTER OUTPUTS BALANCED MASTER OUTPUTS have three separate BALANCED MASTER OUTPUTS BALANCED MASTER OUTPUTS BALANCED MASTER OUTPUTS
conductors, two of which are signal (positive and negative) and one
shield (ground). The balanced line uses a tip-ring-sleeve connection.
Tip = hot or positive (+), ring = cold or negative (-), and sleeve =
shield/ground. The MASTER OUTPUT (5) MASTER OUTPUT (5) MASTER OUTPUT (5) jacks are unbalanced and
MASTER OUTPUT (5)
used to connect to your main amplifier. The REC OUTPUT (7)
can be used to connect the mixer to the record input of your recorder
enabling you to record your mix. The ZONE OUTPUT (6)
you to hook up an additional amplifier.
3 . For your convenience, there are 2 mic inputs (located on the front panel
and the rear panel), however, only one mic input can be used at a time.
The MIC (3) MIC (3) MIC (3) MIC (3) MIC (3) input (found on the rear panel) OR
(found on the front panel) accepts a 1/4" connector and balanced and
unbalanced microphones. The MIC LOOP (14)
and input for connection to an outboard signal enhancer (such as a key
controller, echo/reverb machine, etc...) using a standard balanced cable
with a 1/4" tip/ring/sleeve connector (tip = in, ring = out, and sleeve
= shield/ground).
4 . On the rear panel are 3 stereo PHONO/LINE (9, 12, 13)
LINE (8) LINE (8)
stereo LINE (8) LINE (8) LINE (8) input. The PHONO/LINE
set the (9) (9) input to Phono or Line. The PHONO/LINE (9) (9)
(9)
enables you to set the (12)
SWITCH SWITCH SWITCH SWITCH (15) SWITCH (15) enables you to set the (13) (15) (15) (15)
phono inputs will accept only turntables with a magnetic cartridge.
GROUND SCREWS (2) for you to ground your turntables are located GROUND SCREWS (2) GROUND SCREWS (2) GROUND SCREWS (2) GROUND SCREWS (2)
on the rear panel. The stereo line inputs will accept any line level input
such as a CD player, a cassette player, etc.
5 . Headphones can be plugged into the front panel mounted PHONES
( 4 3 ) j a c k . ( 4 3 ) ( 4 3 ) ( 4 3 ) ( 4 3 )

Operation

Operation
Operation Operation Operation
1 . POWER ON: Once you have made all the equipment connections to
your mixer, press the POWER (1)
2 . CHANNEL 1: The GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), and GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26),
PAN (29) controls allow you to fully adjust the selected source. Switch PAN (29) PAN (29) PAN (29) PAN (29)
# (31) (31) allows you to select the LINE 1/PHONO 1 (13) (31) (31) (31)
PHONO 2 (12) PHONO 2 (12)
PHONO 2 (12) PHONO 2 (12) input. The CHANNEL PHONO 2 (12)
level of this channel.
3 . CHANNEL 2: The GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), GAIN (17), HIGH (20), MID (23), LOW (26), and
PAN (29) PAN (29)
PAN (29) PAN (29) controls allow you to fully adjust the selected source. Switch PAN (29)
(32) (32)
# (32) (32) allows you to select the LINE 3/PHONO 3 (9) (32)
input. The CHANNEL CHANNEL SLIDE CHANNEL CHANNEL SLIDE SLIDE (39) SLIDE
CHANNEL SLIDE
channel.
4 . TONE CONTROLS: There is Low, Mid and High equalization for each
channel with an extremely wide range of adjustment. SUGGESTION:
You can use the Cut Features on each channel to remove Low, Mid
and/or High to create special effects.
5 . INPUT ASSIGN SWITCHES: You can adjust the position of the INPUT
ASSIGN (31, 32) switches to move left to right, up and down OR ASSIGN (31, 32) ASSIGN (31, 32)
ASSIGN (31, 32) ASSIGN (31, 32)
45 degree angle. Make these adjustments with the power OFF.
P a g e 5
MASTER OUTPUT (5)
REC OUTPUT (7) REC OUTPUT (7) REC OUTPUT (7) jacks
REC OUTPUT (7)
ZONE OUTPUT (6) ZONE OUTPUT (6) ZONE OUTPUT (6) jacks allow ZONE OUTPUT (6)
OR OR OR OR the MIC (42) MIC (42) MIC (42) MIC (42) input MIC (42)
MIC LOOP (14) jack acts as an output MIC LOOP (14) MIC LOOP (14) MIC LOOP (14)
PHONO/LINE (9, 12, 13) PHONO/LINE (9, 12, 13)
PHONO/LINE (9, 12, 13) inputs and 1 PHONO/LINE (9, 12, 13)
PHONO/LINE PHONO/LINE SWITCH SWITCH (10) (10)
PHONO/LINE PHONO/LINE SWITCH SWITCH (10) SWITCH (10) (10) enables you to
PHONO/LINE PHONO/LINE PHONO/LINE SWITCH
PHONO/LINE
(12) (12) input to Phono or Line. The PHONO/LINE (12)
(12)
(13) input to Phono or Line. The (13) (13) (13)
POWER (1) POWER (1) POWER (1) POWER (1) switch.
LINE 1/PHONO 1 (13) LINE 1/PHONO 1 (13) LINE 1/PHONO 1 (13) LINE 1/PHONO 1 (13) or the LINE 2/
CHANNEL CHANNEL SLIDE SLIDE (38) (38)
CHANNEL CHANNEL SLIDE SLIDE SLIDE (38) (38) (38) controls the input
LINE 3/PHONO 3 (9) LINE 3/PHONO 3 (9)
LINE 3/PHONO 3 (9) LINE 3/PHONO 3 (9) or the LINE 4 (8)
(39) (39) (39) controls the input level of this
(39)
BALANCED BALANCED BALANCED BALANCED
SWITCH SWITCH (11) SWITCH (11) (11) (11)
SWITCH (11)
PHONO/LINE PHONO/LINE PHONO/LINE
PHONO/LINE
PHONES PHONES PHONES PHONES
LINE 2/ LINE 2/ LINE 2/ LINE 2/
LINE 4 (8) LINE 4 (8)
LINE 4 (8) LINE 4 (8)
INPUT INPUT
INPUT INPUT
OR at a OR OR
OR