HERKULES H-NT 50 Inox Originalbetriebsanleitung Seite 20

the split pin (31) (Fig. 8-10). Push the covers (32)
on to the outside of the wheels (13) so that the
detents engage on the covers (32) for the wheel
(13). (Fig. 11)
Fitting the castors (Fig. 12a-12b)
Fit the castors (12) into the appropriate moun-
tings on the underside of the tank (10). Secure
the castors with the supplied screws as shown in
Fig. 12b.
Fitting the push bar (Fig. 13)
Insert the push bar (35) into the provided push
bar brackets (36) until you feel them latch into
position.
Fitting the appliance head (Fig. 14-15/5)
The appliance head (5) is fastened to the contai-
ner (10) by the locking hook (18). To remove the
appliance head (5), open the locking hook (18)
and remove the appliance head (5). When fi tting
the appliance head (5), make sure that the lo-
cking hook (18) locks into place correctly.
5.2 Fitting the fi lter
Notice!
Never use the wet and dry vacuum cleaner wit-
hout a fi lter.
Check that the fi lter is securely fi tted at all times.
Fitting the foam fi lter (Fig. 16/25)
For wet vacuuming, slip the supplied foam fi lter
(25) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig.3/24) already fi tted upon delivery is not
suitable for wet vacuuming.
Fitting the pleated fi lter (Fig. 17/24)
For dry-vacuuming, slip the pleated fi lter (Fig.
3/24) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig. 3/24) is suitable for dry-vacuuming only.
Fitting the coarse fi lter (Fig. 19a)
The coarse fi lter (16) can be used for suctioning
large amounts of fi ne dust (with or without a dirt
collector bag).
Important! The coarse fi lter is not suitable for
wet vacuuming!
Place the coarse fi lter (16) on the rim of the con-
tainer (10) as shown in Fig. 19a. Ensure that the
coarse fi lter is fi tted completely on the rim of the
container.
Fitting the sealing ring (Fig. 19b)
The sealing ring (37) must fi tted for wet suctioning
and whenever the coarse fi lter is not used.
Anl_H_NT_50_Inox_SPK7.indb 20 Anl_H_NT_50_Inox_SPK7.indb 20
GB
Place the sealing ring (37) on the rim of the con-
tainer (10) as shown in Fig. 19b. Ensure that the
sealing ring is fi tted completely on the rim of the
container.
5.3 Fitting the tank bag (Fig. 18)
Fit the dirt bag (Fig. 3/27) as shown in Figure 18.
5.4 Fitting the suction hose (Fig. 1-3/18)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3/29)
The air regulator (29) can be fi tted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infi nitely ad-
justed using the air regulator (29).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
5.5 Suction nozzles
Dual-purpose nozzle (Fig. 3)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Various attachments can be fi tted to the combi-
nation nozzle depending on what you sort of work
you wish to carry out:
Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
- 20 -
19.02.2018 15:41:59 19.02.2018 15:41:59