Werbung
6
Installation
Contents
• (1) Pair Power Series Full Range Component Speakers
• (1) Pair of grilles/trim rings
• Mounting Hardware
• (1) Set adapter plates (5"x7"/6"x9")
Installation Considerations
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before
attempting to install these
speakers.
2. For safety, disconnect the negative lead from the battery prior to
beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting
your speakers in place.
4. Use high quality connectors for a reliable installation and to minimize
signal
or power
loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel
lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle. If installation in a boat, take care not to
cut
or
drill through the main hull.
6. Never
run
wires underneath the vehicle. Running the wires inside the
vehicle or hull area provides the best protection.
7. Avoid running wires over or through sharp
edges.
Use rubber or
plastic grommets to protect any wires routed through metal, especially
the firewall.
Mounting
Mid-Bass
1. Determine where the speakers will be mounted. Ensure an area large
enough for the
speaker
to mount evenly. Be sure that the mounting
location is deep enough for the speaker to fit; if mounting in a door,
operate all functions (windows,
locks,
etc.) through their entire
operating range to ensure there is no obstruction.
2.
Refer to the specification chart to determine the proper diameter hole
to cut for your speaker model. Cutting and mounting templates can be
found at www.rockfordfosgate.com.
3. Mark the locations for the mounting screws. Drill the holes with a
1/8"
bit.
4. Feed the speaker wires through the cutout and connect to the speaker
terminals.
Be sure to observe proper polarity when
connecting
the
wires.The speaker's positive terminal is indicated with
a"+".
5.
Fit
the trim
ring
over the speaker and mount
into
place using four (4)
screws.
6. Tighten the screws until the speaker is snug in place to prevent
rattling. Do not over tighten the screws.
Mounting tab removal for
some installations
0
Use
pliers
to break
off
plastic
tab.
illus.-2.
1
\
\
l
.
JA,
A
B
reakoff
V
mounting
ta
b.
Example of standard
door installation
.··i~·
. .
~
· ··
...
to Align
Holes
.. ,...
...
··················
i'lus. -2.2
Tweeter- Discreet Dual Clamp (DOC™)
1. Determine where the speakers will be
mounted.
Ensure an area large
enough for the speaker to
mount
evenly. Be sure that the mounting
location is deep enough for the speaker to fit; if mounting in a door,
operate all functions (windows, locks, etc.)
through
their entire
operating range to ensure there is no
obstruction.
2.
Mark the location for the mounting hole. Drill the
hole with
a standard
1.75 inch (45mm) hole
saw.
3. With a single center screw secure the inner
cup
from the front of the
door panel to the outer
cup
from back of the
door
panel.
Tighten
the
screw
until balanced pressure is applied to both faces
of
the
mounting
surface.
4. Feed
the
speaker wires through the cutout and connect to the speaker
terminals.
Be sure to observe proper polarity when
connecting
the
wires. The
speaker's
lead wires
are
indicated with a RED wire "+" and
a BLACK wire"-".
5.
Simply snap the tweeter into place
and
secure with a snap-on trim
ring.
Removal is
easy if
needed.
The protective grille on the tweeter is
non-removable and an
integral
part of the design.
illus.-2.3
Use
tip
o
f
a small
flat
screwdriver
to remove
tweeter
Example of tweeter mounting
using Discreet Dual Clamp (DDC™l
Werbung
