ABBINA Domino Grill Handbuch Seite 6

children), use the lock key (8). While the lock is engaged,
GB
all operation of the keys is disabled, with the exception
of the OFF key (1).
Safety shutdown
In the event that one or more cooking areas is
inadvertently left on, the safety system will shut the
zones down automatically after a certain time has
elapsed, after which the letter "H" will be displayed.
Automatic preheating
This function is designed to facilitate cooking, given that
the cooking cycle may be carried out without the need
for human supervision. The function uses maximum
power to preheat the cooking area to bring it to the
required operating temperature. After a time interval,
the power level automatically returns to the original
setting.
Using the automatic preheating function
Select the required cooking area by means of the key
(2). Select power level 9 by means of key "+" (4), then
press the "+" key (4) again to activate preheating. The
letter "A" will be shown on the relative display. To
preheat the unit with spontaneous movement towards
the required power level (e.g. "6"), set the power to 6
by means of the "-" key (4). After the system has set
to automatic preheating mode, the display panel will
alternate the set power level ("6") and the automatic
preheating function (indicated by the letter "A").
Switching off the automatic preheating function
To deactivate the preheating function (indicated by the
letter "A" on the display), press the "-" key (4) at least 10
seconds since the function has been activated.
Timer function
This function too simplifies operation by not requiring
human supervision during the cooking cycle. Once
the set time on the timer has elapsed, the cooking
area is automatically switched off. If no zone has been
programmed, the timer simply operates as a minute
counter (see the section "Using the timer as a minute
counter").
Using the timer function
1. The cooking area must already be activated with
relative decimal point (12) illuminated.
2. Select a power level between 1 and 9.
3. Press the timer key (6); the timer display shows "00"
and the indicator (10) relative to the zone being
programmed lights up.
4. Select the cooking time (between 0 to 99 minutes) by
means of the "+" and "-" keys (4). The timer will start
up automatically in a few seconds. Press and hold
down the "+" or "-" key (4) to scroll the time setting.
Note that the timer function applies to the selected
cooking area only.
Rapid shutdown of the cooking area and relative timer
Press the "+" and "-" keys (4) at the same time to shut
down the relative cooking area immediately. Note that
the timer function will also be deactivated.
Using the timer as a minute counter
When the timer function is not programmed, the timer
display can be used simply to count down minutes (i.e.
when the displayed time elapses, the cooking area is
not deactivated).
Setting the minute counter
When the unit is off:
1. Press the ON key (1).
2. Press the timer key (6).
3. Use the "+" and "-" keys (4) to set the required time
to be counted back.
When the unit is on and a cooking area is activated:
1. Deselect the zone by pressing the relative key (2);
the decimal point (13) will go out.
2. Press the timer key (6).
3. Set the time required by means of the "+" and "-"
keys (4).
Deactivating the minute counter function
When the set time has elapsed, an acoustic signal is
emitted for two minutes. To silence the signal, press any
key. To interrupt the timer, proceed as follows:
1. Press the timer key (6).
2. Press the "-" key to reset the time (4).
Rapid deactivation of the minute counter
Press "+" and "-" keys (4) at the same time.
Triple circuit function
Switching on one zone
Press key (2/1) to switch on one zone.
Switching on two zones
Press key (2/2) to switch on the central zone and the
circular crown.
Switching on three zones
Press key (2/3) to switch on the central zone, the circular
crown and the external half-crown.
The status of all functions remains as described above.
6