Specifications; Important Safety Instructions - Makita ML120 Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Set plate

SPECIFICATIONS

Model
Bulb .......................................... 12 V 0.7 A
Dimensions
L ............................................. 272 mm (10-11/16")
W ........................................... 94 mm (3-11/16")
H ............................................ 98 mm (3-7/8")
Net weight ................................. 0.26 kg (0.57 lbs)
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Note: Specifications may differ from country to country.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock,
and personal injury, including the following:
READ ALL INSTRUCTIONS.
1. Read this instruction manual and the charger instruction manual carefully before use.
2. This flashlight is not water-proof. Do not use it in damp or wet locations. Do not expose it to rain or snow.
Do not wash it in water.
3. A short-circuit can cause a large current flow, overheating, possible burns and even a breakdown.
(1) Do not touch the inside of the flashlight head with tweezers, metal tools, etc.
(2) Do not touch the battery terminals with any conductive material.
(3) Avoid storing the battery cartridge in a container with any metal objects such as nails, coins, etc.
4. Never expose the battery cartridge to flames, fire or great heat. Breakage may cause release of injurious
material.
5. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It
may result in loss of your eyesight.
6. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
7. Be careful not to drop, shake or strike battery.
8. When the tool is not in use, always switch off and remove the battery cartridge from the tool.
9. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C
(122°F).
10. Do not give the tool a shock by dropping, striking, etc.
11. Do not expose the light to eyes continuously. It may hurt them.
12. Do not cover or clog the lit tool with cloth or carton, etc. It may create a risk of fire.
13. Switch off the light immediately when the lamp gets dark in use. If you leave the lamp switched on, the
battery cartridge capacity may decrease.
14. Do not disassemble the charger or battery cartridge; take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
15. If any problem develops, consult your nearest Makita Service Center or dealer. To maintain product safety
and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service
Center.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Charging
Charge the battery cartridge with the Makita charger before use. To remove the battery cartridge, withdraw it from the
flashlight while pressing the buttons on both sides of the cartridge. After charging, insert the battery cartridge into the
flashlight all the way until it locks in place with a little click. (Fig. 1)
NOTE:
Battery cartridges 1200, 1200A, 1202, 1202A can be used on ML120 if you install the set plate. Install the set plate on
ML120 with the screw provided as shown in Fig. 2.
Explanation of general view
3 Screw
4 Switch
ML120
5
6
ML140
12 V 0.7 A
272 mm (10-11/16")
94 mm (3-11/16")
107 mm (4-3/16")
0.27 kg (0.59 lbs)
Ring
Shoulder strap
ML180
18 V 0.6 A
324 mm (12-3/4")
95 mm (3-3/4")
121 mm (4-3/4")
0.29 kg (0.63 lbs)
9