Assembly - Powerfix Profi Z15003 Montage-, Bedienungs- Und Sicherheitshinweise

Assembly

Q
CAUTION! DANGER OF FIRE! Assemble
and use the product on a fire-resistant surface only.
The following tools are required for
assembly:
7 x Open spanners (1 x 8 mm, 2 x 10 mm,
2 x 14 mm, and possibly 2 x 17 mm)
2 x Allen key
1 x Slotted head screwdriver (approx. 5 mm)
Follow these steps:
j Fasten the saddle
with the hexagonal socket head screws
and washers
34
j Fasten the handle
the projecting screw thread and the corresponding
nut (see Fig. A).
Note: Please bear in mind that the angle
grinder must be fitted with a suitable cutting
disc before assembly. It is not possible to
change the disc with the angle grinder installed
in the stand.
j Now mount the angle grinder in the mount
Note: At this point, first check the size of the
handle thread of your angle grinder. It may be
M6, M8 or M10.
j Then place the corresponding mounting bolts
, , washers
10 11
, distance pieces
14
bushings ,
6 7
j Insert the necessary plastic bushings
into the mounting pieces
Note: Ensure that the size of the plastic bush-
ings , matches the required mounting
6 7
bolts , . Plastic bushings are not required
9 10
for mounting bolts M10
j Screw the matching mounting bolt
through the rear mounting piece
Fasten the rear mounting piece
j
tightening the corresponding size of nut
on the mounting bolt
14
turning it in the direction of the mounting piece
(see Fig. B).
Insert the adjustment screw
j
tom hole and the adjustment screw
79200_HR_GR_content.indd 7
on to the base plate
33
35
(see Fig. A).
on to the mount with
3 36
and matching nuts ,
8 12
, , and plastic
15 16 17
to one side, ready for use.
,
6 7
, (see Fig. B).
18 38
.
11
, ,
9 10
(see Fig. B).
38
in place by
38
,
12
, , (i.e. by
9 10 11
through the bot-
20
through
1
the top hole of the mount
the rubber buffers of these screws must lie
against the angle grinder housing.
Note: First insert these screws so that the rubber
buffers lie directly against the mount
j Now push the plastic locating pieces
mounting pieces
mount (Figure B).
36
j Then attach the mounting pieces
through the plastic locating pieces
hexagonal socket head screws
gated holes in the mount
Place the desired distance piece
j
the mounting bolt
32
on to the front mounting piece
Note: The three distance pieces
are of different lengths. Choose the distance
piece , ,
15 16
Note: Set the distance piece
that the cutting disc cannot come into contact
with the workbench / table below the base
plate (see Figure E).
32
j Screw the matching mounting bolt
through the front mounting piece
. j Fasten the front mounting piece
36
tightening the corresponding size of nut
on the mounting bolt
14
turning it in the direction of the mounting piece
, j Now set the adjustment screws
9
, the angle grinder is aligned at right angles to
13
the base plate
mount .
36
j After slightly loosening the hexagonal socket
head screws
35
the cutting disc of the angle grinder lowers into
centre of the slot provided in the base plate
j Now attach the safety guard
push the safety guard
and fasten it in place with the nut
11
j Now insert the metal rod
sponding opening in the mount
, it in place with the nut
13
bolt (see Fig. C).
40
) Always keep the angle grinder's mains lead in
j
38
place using the clip
After assembly is complete, switch the angle
j
grinder on for a few seconds and then switch it
. Note that later
36
.
36
19
, on to the guide of the
18 38
,
18 38
with the
19
in the elon-
31
(see Fig. A).
36
, ,
15 16
, , and washer
9 10 11
(see Fig. D).
18
,
15 16
of the most appropriate length.
17
, ,
15 16 17
,
9 10
.
18
in place by
18
12
, , (i.e. by
9 10 11
, so that
1 20
and firmly attached to the
32
, adjust the saddle so that
33
. To do this
5
on to the metal rod
5
(see Fig. C).
4
into the corre-
2
and fasten
36
and the mounting
39
.
37
GB/CY
9/3/2012 2:49:56 PM
of the
on
17
8
,
17
so
,
11
, ,
13
).
18
.
32
2
7