Warranty; Maintenance - Felisatti PF180/1500 Bedienungsanleitung

fence if you intend to use it as a guide for making bevel
cuts. (Fig.18)
3. When set at right angle to the planer base, the
fence can be used as a parallel fence guide. (Fig.19)
NOTE: The fence can be fitted to either side of the
base.
NOTE: The angle graduations marked on the fence
are for indicative purposes only. For accurate bevel cutting
it is necessary to measure the angle of the fence, make a
trial cut and adjust if necessary.
SHAVINGS EXTRACTION
1. The dust/chip extraction port (6) allows connection
to a vacuum dust extraction system.
2. Using the dust extraction adapter (18) permits
a dust extraction system to be connected to the dust
extraction port (6).
3. To fit the adapter (18) insert it into the port (6) and
twist it clockwise until it locks into position. (Fig. 20)
The adapter teeth must coincide with the grooves in
the dust extraction port.
DRIVE BELT REPLACEMENT
WARNING: Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades.
1. To replace the drive belt first take out the three
cross-head screws that secure the drive belt cover (17) on
the left-hand side of the planer as viewed from the rear
(Fig. 21).
2. Remove the damaged belt pulling it sideways off
the top pulley and turning the bottom pulley by hand.
Use a soft brush to clean the pulleys and the
surrounding area.
NOTE: Wear eye protection when cleaning out the
pulley area.
3. With the six continuous "V" profiles on the inside,
place the new belt over the bottom pulley. Half fit the other
end of the belt on the top pulley then roll the belt in place
whilst turning the pulley.
4. Check that the belt runs evenly by manually turning
the belt.
5. Replace the cover and the three fixing screws
ensuring that the longer screw is located in the hole at the
front of the cover.
6. Plug the machine, switch it on and run the planer
for a minute to make sure that the motor and belt operate
correctly.
ACCESSORIES
Set of 3 blades (fitted); combined parallel and bevel
fence; dust extraction adapter; blade spanner; 2 knobs for
fitting the combined fence, spare driving belt.

MAINTENANCE

WARNING: Always ensure that the tool is
switched off and unplugged before attempting
to perform any inspections or maintenance.
Regularly check that all the fixing screws are tight.
They may vibrate loose over time. Should any of the screws
be loose, retighten it immediately to avoid hazards.
Re-lubricate all moving parts at regular intervals.
GENERAL INSPECTION
When the carbon brushes are worn out, both brushes
must be replaced simultaneously with genuine brushes at
FELISATTI service centre for warranty and post-warranty
service.
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer or his agent in order to
avoid a safety hazard.
CLEANING
For safe operation always keep the machine and its
ventilation slots clean.
Regularly check to see if any dust or foreign matter has
entered the grills near the motor and around the switches.
Use a soft brush to remove any accumulated dust.
Wear safety glasses to protect your eyes whilst
cleaning. If the body of the tool needs cleaning, wipe it with
a soft damp cloth. A mild detergent can be used.
WARNING: Never use alcohol, petrol or other
cleaning agent. Never use caustic agents to
clean
plastic parts.
WARNING: Water must never come into
contact with the tool.
IMPORTANT! To assure product safety and reliability,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed
by certified service centres or other qualified service
organisations, always using genuine replacement parts.
Notes
Carefully read the entire original instructions before
using this product.
The manufacturer reserves the right to make
changes and improvements to the products and to alter
specifications without prior notice.
Specifications may differ from country to country.
NOISE AND VIBRATION
In developing this tool, special attention was paid to
reducing noise levels.
Despite this, in some cases, the level of noise in the
workplace can exceed 85 dBA. In this case, the operator
should wear ear protection.
Noise and vibration compliance with EN 60745 and
has the following nominal values :
Sound pressure level = 92 dB (A)
Uncertainty КpA 3 dB
Acoustic resonance = 105 dB (A)
Uncertainty КpW 3 dB
Use ear protection!
Vibration acceleration = 4.1 m / s ²
Uncertainty K 1.5 m/s2

WARRANTY

See general warranty conditions printed on the
attached sheet.
DISPOSAL
WARNING! Do not dispose of electric tools in the
household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
9