Herunterladen
Teilen
Diese Seite drucken
Eaton FlexiTech Exit Dual AT L Betriebsanleitung
  1. Anleitungen
  2. Marken
  3. Eaton Anleitungen
  4. Notfallausrüstung
  5. FlexiTech Exit Dual AT L
  6. Betriebsanleitung

Eaton FlexiTech Exit Dual AT L Betriebsanleitung

Vorschau ausblenden Andere Handbücher für FlexiTech Exit Dual AT L:
1
2
3
4
5
6
7

Werbung

Quicklinks

Diese Anleitung herunterladen
Manual
Manuale / Manuel / Betriebsanleitung / Manuál / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja
ZNO2047700 PrC
FlexiTech Exit Dual AT L'
228 mm
x1
x1
1
a
0 V
1
2
c
Drill in the honeycomb zones or in the flexible material.
11/2019
34 mm
x1
x1
x1
b
1
120 mm
228 mm
2,5 mm
Break through a cable
entry using a screwdriver.
B
C
!
Drilling zones to avoid
+ 45°C
+ 5°C
LiFePO
Before use
x2
Ref. 40071352379
Ø 5 mm
F - 1600g
If cable entry on
the right
Min. 5cm
Rigid or flexible wire
2,5 < Ø < 13,5 mm
2
A
24h

Werbung

loading

Verwandte Anleitungen für Eaton FlexiTech Exit Dual AT L

Inhaltszusammenfassung für Eaton FlexiTech Exit Dual AT L

  • Seite 1 Manual Manuale / Manuel / Betriebsanleitung / Manuál / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja ZNO2047700 PrC 11/2019 + 45°C FlexiTech Exit Dual AT L’ + 5°C LiFePO 120 mm Before use 228 mm 34 mm 228 mm Ref.

  • Seite 2: Led Description

    10 wks 10 wks 2 s. Yellow 10 wks 10 wks 10 wks 26 sem/ 26 sem/ 26 sem/ 26 wks 26 wks 26 wks Battery Yellow 0,5 s. Constant Blinking FLEXITECH EXIT DUAL AT L’ ZNO2047700 PrC 11/2019 www.eaton.com...

  • Seite 3: Ceiling Mounting

    Disconnect the battery, wait for 10 seconds, and reconnect it if you decide to change configuration (steps 2-3). PICTOGRAM CONFIGURATION CLICK 2 CLICK 1 CEILING MOUNTING Back See steps 5 c-d. FLEXITECH EXIT DUAL AT L’ ZNO2047700 PrC 11/2019 www.eaton.com...
  • Seite 4 WEEE: Contact your local dealer Eaton Eaton.com/recycling EMEA Headquarters Route de la Longeraie 7 ZNO2047700 PrC- 11/2019 1110 Morges, Switzerland Eaton.eu Eaton is a registered trademark. © 2019 Eaton All trademarks are property 100 % All Rights Reserved of their respective owners.
  • Seite 5 - Cabling of connectors with a screwdriver. - Break through a cable entry using - Drill in the honeycomb - Cabling of connectors by hand. a screwdriver. zones or in the flexible Before use - Rigid or flexible wire material. - Check the packaging for the whole cabling - If cable entry on the right - Drilling zones to avoid...
  • Seite 6 - Even/ Odd Disconnect the battery, - Duration Test - Autotest - LED Description wait for 10 seconds, Day D - Charge / - Green / Yellow - Non-maintained - Installation date and reconnect it if you -Maintained - Battery - Duration Test Lamp / Battery - Constant /...
  • Seite 7 - Magnet Test - Replaceable - Functional Test - Not replaceable Ceiling - Back - Duration Test Pictogram - Battery pack, Order code configuration mounting - See steps 4c-d - Reset luminaire - If the battery duration is insufficient, - DIM level replace the battery.