Specific Safety Instructions; Setting Instructions - Nupower NPE210 Bedienungsanleitung

SPECIFIC SAFETY INSTRUCTIONS

Warning
Some wood and wood type products, especially MDF (Medium
Density Fibreboard), can produce dust that can be hazardous to
your health. We recommend the use of an approved face mask
with replaceable filters when using this machine in addition to
using the dust extraction facility.
Ensure that power tools are disconnected from the mains
supply when not in use, before servicing, lubricating, making
adjustments and when changing accessories such as blades.
Do NOT use blades made from High Speed Steel.
Do NOT stop the blade by forcing the machine or by using
sideways pressure.
Always use the correct type of blade for the operation to be
carried out.
Do NOT use blades that are deformed or have missing teeth.
This is highly dangerous and could result in a serious accident to
the operator and bystanders as well as damaging the machine.
Only use blades that are recommended by the supplier and that
are in good condition.
Do NOT use blades that are larger than specified, only use
blades that are rated for the machine. The rotational speed
(min ) shown on the blade should always be HIGHER than the
-1
rotational speed (min ) of the machine.
-1
Ensure that the directional arrow marked on the blade
corresponds with the rotational direction of the motor. The teeth
of the blade should always point downward as viewed from the
front of the saw.
Do NOT lock the moving guard in the open position.
Ensure that movable guards operate freely without jamming.
Ensure that the retraction mechanism of the guard system
operates correctly.
Keep guards in place and in good working order. With the
machine disconnected from the mains supply check the
operation of the guard to ensure that it operates correctly.
Lower the saw head so that the blade is in its lowest position,
carefully rotate the blade by hand to ensure that it is free from
obstruction.
Repeat this procedure at all maximum mitre and bevel positions
before commencing operation of the mitre saw.
When cutting long work pieces use saw horses or work benches
to support the work piece.
Ensure that all securing clamps are tight and check for excessive
play.
Always keep the blade securing arbor and collars clean.
Whenever replacing blades ensure that the recessed surface
of the blade collar fits snugly against the surface of the blade.
Ensure that the blade securing bolt is securely tightened using
the wrenches provided. Do not over tighten.
Before commencing any cut allow the blade to reach its
full speed, let it run for a few seconds. If any unusual noise
or vibration is heard STOP the machine immediately, and
investigate the cause.
Never try to cut free hand. Always ensure that the work piece
is securely pressed against the back fence and table support
surface.
Ensure that the work piece that is being cut off has sufficient
room to move sideways. Failure to do so may result in the off
cut binding against the blade.
If the work piece cannot be held securely by hand then use the
jig or clamp to hold it in place whilst it is being cut.
Ensure that irregular or round pieces are held securely and are
unable to move or twist so that they do not pinch the blade.
Never cut more than one piece at a time.
Never cut pieces that are too small to be held securely against
the back fence with the thumb and index finger.
Use only blades that are recommended by the manufacturer.
Do NOT start the machine with the blade in contact with the
work piece.
Check the work piece for any protruding nails, screw heads or
anything that could damage the blade.
Do NOT attempt to modify the machine or its accessories in
any way.
Approved ear defenders should be worn when using mitre
saws.
ASSEMBLY INSTRUCTIONS
MOUNTING THE MACHINE (1)
The machine has four mounting holes in its base (1.1). These
can be used to permanently secure the saw to a workbench
with suitable screws or bolts. Alternatively, if the machine needs
to be moved frequently it can be secured to a base of 19mm
plywood to provide a more stable base.
Fit the dust bag over the extraction outlet locating the spring clip
in the groove on the outlet spigot (2).
Caution
When boxed or during storage and transportation the saw head
is locked in the down position. To release the head ready for
operation apply downward pressure to the handle and pull out
the lock pin (3) and allow the head to rise gently to its upper
position.

SETTING INSTRUCTIONS

ADJUSTMENT NECESSARY BEFORE THE MACHINE
CAN BE USED
The following adjustments must be made before operating the
saw. This is to ensure accuracy and safety when in operation.
Warning! Always ensure that the machine is disconnected from
the power supply before any maintenance or adjustments are
carried out.
BLADE TO TABLE ALIGNMENT
Position the rotating table to the 0° position (90° to the work
support fence). Position the saw head to the 90° bevel position.
(90° to the rotating table).
Depress the guard locking lever (4) and lower the blade into
the table slot.
If the blade is not parallel to the table slot loosen the three
socket cap screws (5) and turn the saw head until parallel. Re-
secure the three screws (5.1).
21
GB