Maintenance - Stomer Professional SAD-14x2-D Bedienungsanleitung

English
Cordless drill/driver
INTENDED USE
• This tool is intended for drilling in wood, metal, ceramic
and plastic; tools with electronic speed control and left/right
rotation are also suitable for screwdriving and thread cut-
ting
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
5 Switch for selecting mechanical speed
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
• Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
• Recharge only with the charger specifi ed by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fi re when used with another bat-
tery pack.
• Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk
of injury and fi re.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger (charg-
ers with a rating of 230V or 240V can also be connected
to a 220V supply)
• In case of electrical or mechanical malfunction, imme-
diately switch off the tool or unplug charger from power
source
• SBM Group can assure fl awless functioning of the tool
only when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• This tool should not be used by people under the age
of 16 years
• Be careful not to drill or drive into areas where electrical
wires may be contacted
• Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories
as well as when carrying or storing the tool
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where tempera-
ture will not exceed 40° C or drop below 0° C
• Batteries will explode in fi re, so do not burn battery for
any reason
1
2
• When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, fl ush eyes with clean water
for a minimum of 10 minutes and seek immediately medi-
cal attention
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc.
to prevent short-circuit
• Do not use charger when damaged; take it to one of
the offi cially registered SBM Group Service Stations for
a safety check
• Do not use battery when damaged; it should be re-
placed immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries
with the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of the charger to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left unat-
tended
To ensure longer service life and proper per-
formance of the battery, take the following ac-
tions when you start using new battery:
1. Use the new battery, without recharging it, till its com-
plete discharge.
2. Then charge the battery for 1 hour.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here
they will be disposed of in an environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal
site for chemical waste so that they can be recycled or dis-
posed of in an environmentally friendly manner.
6