OKBABY BODY GUARD Handbuch Seite 8

holes (7).
Illustration 7:
Adjust the vertical position according to the parameters shown
in the diagram. If the child seat is too high or too low, loosen the
screws (8) on the fastening block and adjust the height. Use the
centre-point mark (21) printed on the child seat to achieve the
correct horizontal position. To adjust the horizontal position of the
seat, position the support arm (4) in one of the three slots under the
child seat base (ill. 2). When the seat is correctly in place, tighten
the screws (8) slowly and evenly until the fastening block stops
rotating around the frame. Slide the front cover (17) over the front
part of the block. Cover the fastening counter-block (6) with the
protection cover (10).
Illustration 8:
Insert the foot straps (19) into both of the footrests passing them
through the widest part of the external slot (a) to the internal slot (b).
Illustration 9:
Fastening the footrest. Fasten the footrests (15) by inserting them
in a position higher than its shaped seat, passing the widest part of
the foot strap through the slit on the leg of the child seat (ill. 9A).
Position the right footrest, into the slot on the right of the seat and
vice versa. For each footrest, insert the regulating pin (16) from the
outside of the seat towards the inside, making sure the right pin
coincides with the right side and vice versa.
Illustration 10:
Extracting the footrest. To extract the footrests, turn the regulat-
ing pin (16) upwards, move the footrest (15) upwards as far as pos-
sible, open the foot strap and pull the regulating pin lever outwards
to free the support.
Use of the seat:
Illustrations 11-12:
Adjusting the footrests: Unhook the strap on the outer side (B) of
the regulating pin. To adjust the height of the footrest (15), rotate
the regulating pin (16) upwards; once you have found the desired
position, turn the pin downwards to fix the footrest in place. Re-
place the foot strap.
Illustrations 12-13:
Fastening and unfastening the child's feet: To hold the child's
feet in position, fix the foot strap on the inside of the regulating pin
(ill. 13, A) and then fasten it to the outside (ill. 13,B). To release the
foot strap follow the procedure in reverse. Always make sure your
child's feet are well fastened to the footrests. The safety belt is long
10 Body Guard Rear child's seat
for easy adjustment.
DANGER: always hook the foot straps onto both sides of the fasten-
ing pins to prevent them from coming into contact with the wheel
spokes.
Illustrations 14-15:
Fastening the child's safety belt: Adjust the height and length of
the belts according to the size of the child. Setting belt height: the
belt can be extracted to adjust its height by inserting the buckle
behind the backrest through the opening each time (fig.15). Choose
the upper or lower openings to fix the belts based on the child's
height. Setting belt length: modify belt length by sliding the buck-
les. The belts must be fastened firmly without them being too tight
for the child.
Fastening the belts:
Fasten the belt clasp. Check that the belt clasp clicks shut properly,
and then pull the belt.
Illustration 16:
Press simultaneously the two press-buttons (front and rear) on the
clasp. The clasp will open.
Illustration 17:
Removing the child seat Press the release button (7) on the fasten-
ing block and remove the child seat. To hook the seat on again,
insert the support arm (4) in the two fixing block holes (7) until the
lever clicks (fig.6).
Maintenance
1) Clean the seat, the padding and the belts with warm water and a
mild detergent. Do not use solvents or abrasive or corrosive de-
tergents. Leave the padding to dry in the open air. Do not iron
2) Seat repairs and replacement of damaged components must
only be carried out by authorized personnel.
Technical specifications
Product Child bicycle seat OKBABY mod. Body Guard
Dimensions 73x43x57 CM (LxDxH)
Weight 4Kg
Body Guard Rear child's seat 11