Eneral Notes On Safety; Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER ABRASIVE SUNmic 60 Originalbetriebsanleitung

1. n
1.1 g

EnErAL noTES on SAfETy

These technical document apply to the SUNmic 60 con-
trol unit.
The control unit may only be handled by person-
nel who are qualified.
Hold power tools by insulated gripping surfaces
when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
«live» wire will make exposed metal parts of the tool «live»
and shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 U
SE of ThE mAchinE for pUrpoSES for
which iT iS inTEnDED
This control unit is only intended to be used with tools of
a maximum diameter of 45 mm for grinding, milling, pol-
ishing, deburring, engraving, satin finishing and brushing
processes.
1.3 i
ncorrEcT USE
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 Ec
DEcLArATion of conformiTy
Otto Suhner GmbH of Trottäcker 50, D-79701 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 07/2017.
M. Voyame/Division manager
2. c
2.1 p
rior To TAKing ThE mAchinE inTo SErVicE
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check grinding tool
prior to use. The maximum allowable speed of the tool
and of the chuck may not be exceeded under any circum-
20
S
oteS on afety
ommISSIonIng
stances. Observe national regulations.
Remove safety guard.
2.2 T
AKing ThE mAchinE inTo SErVicE
2.2.1 c
onnEcTing ThE conTroL UniT To A powEr SUppLy
Connect the mains cable to the control unit and connect
it to the power supply.
2.2.2 A
SSEmBLing ThE hAnD TooL
Only utilize hand tools which have been approved
by SUHNER. For more detailed information, see
technical document for the hand tool used.
Connecting/removing hand tool. «A/B» (BLDS Motos),
«C» (carbon brush motors).
2.2.3 g
rinDing TooLS
For more detailed information, see technical document
for the hand tool used.
2.3 r

ATing DATA

Power Input
Power voltage
Mains fuse
Insulation class
Overload protection
Weight without cable
Length/width/depth
2.4 o
pErATing conDiTionS
Temperature range during operation: 0 to +40°C
Relative air humidity: 85 % at +10°C not condensed
max. 250W
90-240V, 50-60Hz
16A
IP 30
yes
2.4kg
135x240x200mm