Specifications; Audio Inputs; Audio Outputs - Tascam MZ-123BT Installationsanleitung

Sound via Bluetooth breaks up or is noisy.
p Are there any wireless LAN devices, other Bluetooth devices,
microwave ovens or similar equipment nearby?
Keep such devices as far away as possible during use.
p Try reducing the distance between this unit and the other
Bluetooth device. Try changing the positions of this unit and
the other Bluetooth device.
p The operation of apps other than for music playback on the
smartphone could cause the sound to break up. In this case,
stop operation of apps other than the one used for music
playback.
Cannot connect or communication is
interrupted when using Bluetooth.
p Confirm that the other Bluetooth device power is on and that
its Bluetooth function is on.
p Confirm that the other Bluetooth device is not too far away.
Are there walls or other obstacles, for example, between this
unit and the other Bluetooth device?
Try changing the positions of this unit and the other
Bluetooth device.
p Turn OFF and restart the MZ-123BT.
p Remove the "MZ-123BT" pairing record from the other
Bluetooth device, and try pairing the unit with that Bluetooth
device again. (See "Connecting with Bluetooth devices" on
page 14)
Cannot pair with another Bluetooth device.
p Confirm that the other Bluetooth device supports A2DP.
p Confirm that the other Bluetooth device is in a state that
allows transmission. For details, check the operation manual
of that Bluetooth device.
p Turn the power off for both this unit and the other Bluetooth
device once, turn them both on again and try pairing them.
p Turn off Bluetooth devices other than the one that you are
trying to pair with.
p Remove the "MZ-123BT" pairing record from the other
Bluetooth device, and try pairing the unit with that Bluetooth
device again. (See "Connecting with Bluetooth devices" on
page 14)

Specifications

Audio inputs

MIC INPUT (BALANCED) jack (front)
Connector:
XLR-3-31 equivalent
(1: GND, 2: HOT, 3: COLD)
6.3mm (1/4") standard TRS jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Rated input level:
-26 dBu (0.039 Vrms, when FRONT HIGH)
-2 dBu (0.616 Vrms, when FRONT LOW)
Maximum input level:
-10 dBu (0.245 Vrms, when FRONT HIGH)
+14 dBu (3.884 Vrms, when FRONT LOW)
Minimum input level:
-65 dBu (0.0004 Vrms, when FRONT HIGH)
-41 dBu (0.007 Vrms, when FRONT LOW)
Gain adjustment range: 39 dB
Input impedance: 2.2 kΩ
MIC IN 1-2 (BALANCED) connectors (rear)
Connectors: Euroblock (balanced) 3.81mm pitch
Rated input level:
-26 dBu (0.039 Vrms, when PAD switch OFF)
-2 dBu (0.616 Vrms, when PAD switch ON)
Maximum input level:
-10 dBu (0.245 Vrms, when PAD switch OFF)
+14 dBu (3.884 Vrms, when PAD switch ON)
Minimum input level:
-65 dBu (0.0004 Vrms, when PAD switch OFF)
-41 dBu (0.007 Vrms, when PAD switch ON)
Gain adjustment range: 39 dB
Input impedance: 2.2 kΩ
LINE INPUTS 1-2 (UNBALANCED) connectors
(rear)
Connectors: RCA pin jacks
Nominal input level: -10 dBV (0.316 Vrms)
Maximum input level: +6 dBV (2.0 Vrms)
Gain adjustment range: ±16 dB
Input impedance: 10 kΩ or higher
AUX IN (UNBALANCED) jack (front)
Connector: 3.5mm (1/8") stereo mini jack
Nominal input level: -20 dBV (0.1 Vrms)
Maximum input level: -4 dBV (0.63 Vrms)
Input impedance: 10 kΩ or higher

Audio outputs

OUTPUTS (BALANCED) connectors
Connectors: Euroblock (balanced) 3.81mm pitch
Rated output level:
+4 dBu (1.228 Vrms, when VOLUME knob at 0 dB)
Maximum output level:
+24 dBu (12.282 Vrms)
Output impedance: 200Ω
PHONES jack
Connector: 6.3mm (1/4") standard stereo jack
Maximum output: 80 mW + 80 mW or higher
(THD+N 0.1% or less, into 32Ω load)
17
TASCAM MZ-123BT