Product Overview; Package Contents; Explanation Of Symbols; Safety Instructions - Renkforce AC750 Bedienungsanleitung

Operating instructions
WLAN Repeater AC750
Item no. 1902085
Intended use
The product has three operating modes – repeater, access point (AP) and router.
The repeater mode serves to amplify your existing WLAN network and enlarge the coverage
area.
The access point (AP) operating mode provides a separate WLAN network.
The router mode is used to connect devices connected to the product to the Internet via your
existing modem.
You can connect your devices to the product in all operating modes via WLAN or LAN.
Power is supplied via the mains socket in which the product is plugged in.
If you use the product for other purposes than those described above, the product may be
etc. Please read the operating instructions carefully and do not discard them. If you pass the
product on to a third party, please include the operating instructions.
This product complies with the applicable national and European regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.

Package contents

• WLAN Repeater AC750
• RJ45 cable
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown here. Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of per-
sonal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in these operating
instructions which absolutely have to be observed.

Safety instructions

Please read the operating instructions carefully and pay particular attention
to the safety instructions. We do not assume liability for any injuries/mate-
rial damages resulting from failure to observe the safety instructions and the
information in these operating instructions for the proper use of the product.
Furthermore, in such cases, the warranty/guarantee will be null and void.
• The design of the product complies with the safety class II. Only a standard mains
socket connected to the public supply may be used as the power source for the
device.
• If the product is damaged, do not touch it; there is a danger to life from electric
shock!
Switch off the mains voltage to the mains socket to which the power adapter is
connected (e.g., switch off at the corresponding circuit breaker or remove the safe-
ty fuse and then switch off the corresponding RCD). Now disconnect the power
adapter from the socket and take the product to a specialized workshop.
• Check the product for damage before each use!
• If you detect any damage, DO NOT connect the product to the mains supply!
Danger to life!
• The product is only suitable for dry, enclosed indoor areas. The product must not
get damp or wet; never handle it if your hands are wet!
Danger of electric shock!
• Protect the product from extreme temperatures, direct sunlight, strong vibrations,
high humidity, moisture, combustible gases, vapours and solvents.
• The product is not a toy. Keep out of the reach of children and pets.
• Do not carelessly leave the packaging material lying around, since it could be-
come a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows or falls even
from a low height.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.

Product overview

1 Recessed RESET button
2 WPS button
3 On/off slide switch
4 LAN connection
5 WAN/LAN connection
6 Slide switch for mode selection
7 Status LEDs
Power (lights up, as soon as the device is switched on)
LAN
WAN/LAN
WPS
connect to a device)
WiFi LEDs (indicates the signal strength, 3 LEDs 100%, 2 LEDs 50% - 75%, 1 LED below
Default settings:
admin
Connection and start-up
• Plug the device into a mains socket.
• Adjust the antennas depending on your use as shown in the two images.
• Use the mode selection slide switch (6) to select the desired mode. The operating modes
repeater, access point (AP) and router can be selected.
• If you selected access point mode, connect the WAN/LAN port to a network port on your
router using a 1-to-1 network cable.
• If you selected router mode, connect the WAN/LAN port using a 1-to-1 connected network
cable to the corresponding port of your modem. Switch on the modem.
• Switch on the product using the slide switch (3) (position ON) and wait until the starting
process is completed. It takes approx. 2 minutes.
http://ap.setup
192.168.10.1
admin