Home Automation - Blaupunkt Q-series Schnellstartanleitung

11. Home Automation

To make any changes to your Home Automation you need to go to the Home Portal
"eu.bphomeconnect.com".
Device - Allows you to manage and use
individually all the Home Automation accessories.
Room - Assign each accessories to the appropriate
room for easier management. (only for Home
Automation accessories)
Group - You can add accesories of the same type
to a group to manage all the accesories with a
single command.
Scenario - Create your scenario to define preset
actions for your Home Automation accessories.
Scenarios can be triggered via the scenario swich
selector (SSW-S1) or your mobile. The maximum
amount of actions per Scenario is 5.
Rule - Create your rule to initiate automatic actions
of your panel and Home Automation devices
under a trigger & conditions.
How to create a rule:
Recomended Rules
Whenever there is an alarm Turn the
lights ON, roll the blinds UP and start a
video recording.
When you open the door of your
home between 19:00 and 7:00 turn
the lights ON for 20s
Simulate presence when you are on
holidays:
Eveyday at specific times e.g. 20:00 the
blinds will turn UP and the light will turn
ON by 30minutes. "
Everyday at 6:00 change the Security
system to disarm and open your blinds
Whenever you Arm the system turn
OFF your lights, turn down the heating
system to 18ºC and close your blinds
Everyday at 23:00 change the Security
system to Home arm, turn all the lights
OFF, close all your blinds and turn
down the heating system to 18ºC.
Step 1: Go to Automation - Rule and click the + button.
Step 2: Write a name for the rule, e.g. "Auto Arm".
Step 3: Select a trigger for the rule. (e.g. "Schedule" --> "Every Week"
select the days and time)
Step 4: If you want, add any condition (status of system for the rule
to happen). E.g time period or system mode, up to 2 conditions.
Step 5: Select from the list an action to trigger rule. E.g. Device
action --> Power swich ( PSM-S1) to Switch On.
Step 6: If you would like to add more actions press the +
button on the right (up to 5 actions are possible).
Step 7: Click "Submit" to save the changes.
Trigger Condition
Trigger alarm None
Alarm --> Any
alarm
Door Contact Time Period -->
Open Daily --> From
19:00 to 7:00
Schedule --> None
Weekly ->
Everyday 20:00
Schedule --> None
Weekly ->
Everyday 6:00
Mode Change None
--> Arm
Schedule --> None
Weekly ->
Everyday 23:00
Action
"Device Action --> Power Switch PSM-S1 or PRM2-S1 --> ON
Device Action --> Roller Shutter SCM-S1 Open 100%
Request Video --> IPC-S1"
Device Action --> Power Switch PSM-S1 or PRM2-S1 --> ON for -> 20 seconds
"Device Action --> Power Switch PSM-S1 or PRM-S1 --> ON for -> 30min
Device Action --> Roller Shutter SCM-S1 Close"
"Mode Change --> Disarm
Device Action --> Roller Shutter SCM-S1 Open 100%"
"Device Action --> Power Switch PSM-S1 or PRM-S1 --> OFF
Device Action --> Thermostat TRV-S1 or TMST-S1 --> ON ->18ºC
Device Action --> Roller Shutter SCM-S1 Close"
"Mode Change --> Home Arm
Device Action --> Power Switch PSM-S1 or PRM-S1 --> OFF
Device Action --> Roller Shutter SCM-S1 Close
Device Action --> Thermostat TRV-S1 or TMST-S1 --> Turn Down to 18ºC"
13