Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DESCRIPTION OF COMPONENTS
GB / US
US
/
(1) Rating plate
(2) Safety suspension
(3) Anti-crash safety device
DESCRIPTION OF COMPONENTS
INTRODUCTION
(4) Elastic cable stop buffer
(1) Rating plate
These Instructions for Use have been compiled for zero gravity balancers of the following type se-
(5) Cable clamp
ries: EB28, EB30, EB35 and EB45.
(2) Safety suspension
(8) Shaft (for load adjustment)
Whereas the basic design of these balancers is the same in all cases, each type series is designed
(3) Anti-crash safety device
for a s pecific load range and a s pecific cable extension range. Accordingly, the balancer types dif-
(9) Load hook
(4) Elastic cable stop buffer
fer in their dimensions. For details, please refer to the "Technical characteristics" section.
(10) Adjusting screw (worm)
(5) Cable clamp
These Instructions for Use provide the information required both for installation of the zero gravity
(11) Ratchet lock
(8) Shaft (for load adjustment)
balancers by adequately trained technical personnel and for their proper handling and use by spe-
(12) Cover disk
(9) Load hook
cially instructed personnel.
(10) Adjusting screw (worm)
As regards maintenance and repair work, special Service Instructions are available at our website
Note, however, that only adequately trained technical personnel is permitted to perform such work.
(11) Ratchet lock
(12) Cover disk
MANUFACTURER'S DETAILS
INTENDED USE
Carl Stahl Kromer GmbH
The zero gravity balancer is exclusively designed for relieving (counterbalancing) the weight of
Naegelseestrasse 37
hand-held tools (such as drilling machines, screwdrivers, welding tongs, slaughterhouse ma-
D-79288 Gottenheim
chines) and feed lines (such as cables and hoses) during work.
INTENDED USE
Any other or additional use shall be considered non-intended use! The manufacturer/supplier
EC Declaration of Conformity
The zero gravity balancer is exclusively designed for relieving (counterbalancing) the weight of
shall not be responsible for any damage resulting from such use. The risk posed by improper use
We hereby declare with sole responsibility that the zero gravity balancers have been developed,
hand-held tools (such as drilling machines, screwdrivers, welding tongs, slaughterhouse ma-
shall be borne by the user alone.
chines) and feed lines (such as cables and hoses) during work.
designed and manufactured in compliance with the applicable EC Directive 2006/42/EC on ma-
The zero gravity balancer may only be operated within the load range specified on the rating
chinery.
Any other or additional use shall be considered non-intended use! The manufacturer/supplier
plate.
The following standards have been applied: DIN EN ISO 12100 and DIN 15112.
shall not be responsible for any damage resulting from such use. The risk posed by improper use
Using the balancer outside the field of application described above shall void the warranty unless
shall be borne by the user alone.
Documentation officer: Carl Stahl Kromer GmbH, tel.: +49 (0) 7665 / 50 207-0
the written consent of Carl Stahl Kromer GmbH was obtained beforehand.
This EC Declaration of Conformity shall become invalid if the zero gravity balancers are rebuilt or
The zero gravity balancer may only be operated within the load range specified on the rating
The zero gravity balancer may only be operated, installed, serviced and repaired by specially
plate.
modified in any way.
trained personnel.
Using the balancer outside the field of application described above shall void the warranty unless
Thomas Steinle
Thomas Steinle
the written consent of Carl Stahl Kromer GmbH was obtained beforehand.
IMPROPER USE
The zero gravity balancer may only be operated, installed, serviced and repaired by specially
Thomas Steinle
The zero gravity balancer must not be used as a c rane.
trained personnel.
Managing Director
The drum lock must not be used for load replacement.
IMPROPER USE
WARRANTY
SAFETY INSTRUCTIONS – ACCIDENT PREVENTION
The zero gravity balancer must not be used as a c rane.
We warrant the zero gravity balancers to be free from defects in material for a p eriod of 24 months,
No changes may be made to the balancer or its accessories without the express written consent
The drum lock must not be used for load replacement.
starting on the date of delivery. This warranty excludes the consequences of normal wear and tear,
of the manufacturer.
overload, improper use and use of non-original (third-party) spare parts.
The safe use of this product is only ensured if you have fully read and understood these user and
SAFETY INSTRUCTIONS – ACCIDENT PREVENTION
Claims under this warranty can only be accepted if the product is handed over to us in undismantled
safety instructions and observe them strictly during work.
condition for examination. Any damage due to faulty materials or manufacturing defects will be rem-
No changes may be made to the balancer or its accessories without the express written consent
The balancer may only be operated and installed by specially trained personnel. These persons
edied free of charge through replacement or repair. Our Standard Terms and Conditions shall apply
of the manufacturer.
must previously have been informed about the potential hazards involved in performing these
exclusively.
The safe use of this product is only ensured if you have fully read and understood these user and
tasks.
safety instructions and observe them strictly during work.
The balancer may only be serviced and repaired by qualified personnel that has been specially
RATING PLATE
The balancer may only be operated and installed by specially trained personnel. These persons
trained or authorized by the manufacturer.
The rating plate is attached to the body of the balancer.
must previously have been informed about the potential hazards involved in performing these
Taking the balancer apart is extremely dangerous and therefore strictly forbidden.
tasks.
It provides detailed information regarding the manufacturer, the type series and the approved
The fixtures to which the zero gravity balancer and the anti-crash safety device are to be fastened
load range of the zero gravity balancer.
The balancer may only be serviced and repaired by qualified personnel that has been specially
must provide sufficient stability!
trained or authorized by the manufacturer.
Never operate the zero gravity balancer without the safety equipment supplied (anti-crash safety
TECHNICAL CHARACTERISTICS
Taking the balancer apart is extremely dangerous and therefore strictly forbidden.
device) in place.
For the specifications of each type of balancer, please refer to page 10.
The fixtures to which the zero gravity balancer and the anti-crash safety device are to be fastened
must provide sufficient stability!
ID No.
Never operate the zero gravity balancer without the safety equipment supplied (anti-crash safety
device) in place.
ID
32
24
Instructions for Use – Zero Gravity Balancers
Instructions for Use – Zero Gravity Balancers
Instructions for Use – Zero Gravity Balancers
Tel.: +49 (0) 7665 / 50 207-0
FAX: +49 (0) 7665 / 50 207-22
Own Weight
(kg)
G
Only 7241 0800 81...87
(13) Manual drum lock
Only 7248:
Only 7241 0800 81...87
(14) Cable guide nozzle
(13) Manual drum lock
(15) Cable mouth
(16) Cable coupling screw
Only 7248:
(17) Cable coupling bush
(14) Cable guide nozzle
(18) Swivel
(15) Cable mouth
(19) Load cables (2 items)
(16) Cable coupling screw
(20) Transport clamp
(17) Cable coupling bush
(18) Swivel
Only 7261:
(19) Load cables (2 items)
(21) Pulley
(20) Transport clamp
Only 7261:
(21) Pulley
Gottenheim,
26.03. 2019
Load Range
Cable Exten-
(kg)
K
L
Email:
info@easy-balancer.com
Website: www.easy-balancer.com
B. Lhd
Bernd Lienhard
Head of Quality Assurance
Max. Preload
sion (m)
(approx.) X
GB / US
GB / US
33
(Turns)
33
Werbung
Inhaltsverzeichnis
