Battery Installation - Bladez Toyz Hotwheels Rc Drone Racerz Bedienungsanleitung

STUNT BUILD / CONSTRUCTION VOLTIGE / STUNT-AUFBAU / STRUTTURA STUNT / ESTRUCTURA DE ACRO-
BACIAS / STUNTCONSTRUCTIE / / KASKADÉRSKÁ DRÁHA
Note: The stunt set is compatible with official Hot Wheels orange track (not included - sold separately). Remarque : Le jeu de voltige est compatible
avec la piste orange orange Hot Wheels (non incluse - vendue séparément). Hinweis: Das Stunt-Set ist mit den offiziellen orangen Hot Wheels
Schienen kompatibel (nicht enthalten - separat erhältlich). Nota: Il set stunt è compatibile con Orange Track di Hot Wheels (non incluso - venduto
separatamente). Nota: El juego de acrobacias es compatible con la pista naranja oficial de Hot Wheels (no incluida, se vende por separado). Let op: de
stuntset is compatibel met het officiële oranje Hot Wheels-circuit (niet meegeleverd, wordt afzonderlijk verkocht). Poznámka: Souprava pro
kaskadérské kousky je kompatibilní s oficiální oranžovou dráhou Hot Wheels (není součástí – prodává se samostatně).
2 Metres
Note: Operating the toy on track requires skill. For best performance, play on a hard smooth surface. Remarque : L'utilisation du jouet sur piste
nécessite des compétences. Pour de meilleures performances, jouez sur une surface dure et lisse. Hinweis: Der Betrieb des Spielzeugs auf Schienen
erfordert Geschick. Spielen Sie für eine optimale Leistung auf einer harten, glatten Oberfläche. Nota: Il funzionamento del giocattolo su una pista
richiede abilità. Per ottenere prestazioni eccellenti, farlo funzionare su una superficie dura e liscia. Nota: Utilizar el juguete sobre pistas requiere
habilidad. Para un mejor rendimiento, juegue sobre una superficie lisa y dura. Let op: voor het besturen van het voertuig op het circuit is enige
vaardigheid nodig. Speel met het voertuig op een hard, glad oppervlak voor het beste resultaat. Poznámka: Provoz hračky na dráze si vyžaduje
ENGLISH
GB
B. BATTERY INSTALLATION
1. Use the screwdriver provided to remove the screw from the battery cover at
the back of the handset. 2. Place 4x 1.5V AA / LR6 non-rechargeable batteries
in the battery compartment, as per the polarity shown inside. 3. Replace the
battery cover and tighten the screw. Batteries to be replaced by an adult. New
non-rechargeable alkaline batteries are recommended for optimum use and
maximum performance. Drone LED lights will flash when low battery.
C. CHARGING FROM COMPUTER
The Drone Racer is supplied with an initial charge allowing you to start using
straight away. To prevent overcharging the battery please ensure the battery is
fully discharged before recharging. 1. Ensure the Drone Racer is switched off.
2. Plug the USB into a computer/USB port. DO NOT plug the USB charger
into an AC Adapter. 3. Insert the USB cable pin connector in to the Drone Racer
battery port, located on the back of the drone. Be careful not to force the
connectors as it may cause damage. The RED LED on the USB will turn on,
indicating that the Drone Racer is charging. 4. The Drone Racer is charged after
approximately 60 minutes. The RED LED on the USB will go out, indicating that
the Drone Racer battery is fully charged. 5. Remove the USB cable pin
1 Metre
určité dovednosti. Nejlepších výsledků dosáhnete na tvrdém rovném povrchu.
dass der Drone Racer vollständig aufgeladen ist, bevor Sie
versuchen, das Looping zu fahren. Prima di provare a percorrere
l'anello, ccertare che Drone Racer sia completamento carico.
Asegúrese de que el Drone Racer esté completamente cargado antes de intentar
una pirueta. Zorg dat de Drone Racer volledig is opgeladen voordat je de looping
probeert. Před jízdou na smyčce se ujistěte, že je výrobek Drone Racer zcela nabitý.
connector from the Drone Racer battery port once the charging is complete.
DO NOT OVERCHARGE. Flight time 5-6 minutes. Drive time 4-5 minutes.
D. CHARGING FROM HANDSET
1. Ensure the Drone Racer is switched off. 2. Plug the USB cable into the
Drone Racerz Handset and switch the handset on. The USB port is located
on the back of the handset. 3. Repeat steps 3-5 in 'Charging from
Computer' . DO NOT OVERCHARGE. Flight time 5-6 minutes. Drive time 4-5 minutes.
E. SYNCHRONISE - IMPORTANT!
1. Ensure 'Control Stick A' is positioned down fully before synchronising the
handset and Drone Racer. 2. Switch on the Drone Racer. The GREEN and RED
LED lights on the Drone Racer will flash. The Drone Racer is now ON. 3. Place
the Drone Racer on a FLAT SURFACE with the black blades furthest away from
you. If the Drone Racer is not positioned on a flat surface, this may prevent
the Drone Racer blades from spinning correctly. 4. Turn the handset ON. The
handset will beep. The GREEN and RED LED light on the Drone Racer will stop
flashing. 5&6. Slowly push 'Control Stick A' up and then down to pair the
handset with the Drone Racer. 7. The handset and Drone Racer are now
synchronised and active. 8. Slowly push 'Control Stick A' up and the rotor
blades will start to rotate. 9. Your Drone Racer will start to take off.
7
Ensure Drone Racer is fully charged
before attempting to drive the loop.
Assurez-vous que le Drone Racer soit
omplètement rechargé avant d'essayer
de piloter en boucle. Stellen Sie sicher,