Vitek VT-4225 CA Betriebsanweisung Seite 7

Remove the lid (8) by turning the lid (8) so
–
that the mark ▲ located on the unit body
above the display is opposite the mark
the lid (8)
Remove the bowl (6) and put the food into
–
the bowl following the recipe (see the Recipe
book).
Install the bowl (6) in the process chamber.
–
Before installing the bowl (6), make sure that
the outer surface of the bowl is clean and dry,
and the bowl itself is placed evenly and is in
secure contact with the surface of the heat-
ing element (14).
If you steam products, pour water into the bowl
–
(6) so that boiling water doesn't reach the bot-
tom of the basket (21). Put the food into the
basket (21) and place it on the bowl (6).
If you are cooking in the «Roasting» program,
–
do not install the lid (8).
Before installing the lid (8), check the valve
–
and the blocking system elements (9). They
should be clean and the blocking system valve
(9) should be lowered.
Place the lid (8) on the unit so that the mark
–
▲ located on the unit body above the display
is opposite the mark
Turn the lid (8) in the direction of the symbol
–
as far as it will go.
Insert the power cord connector into the con-
–
nection socket on the multicooker body and
the power cord plug into the mains socket. You
will hear a sound signal, the «----» symbols will
be shown on the display (3) (sleep mode).
To cancel the sleep mode, press the ON/OFF
–
button (19) . Symbols «88:88» will appear
on the display (3).
Setting an automatic cooking program
3.
Touch the «MENU» button (16) and then select
the cooking program with the buttons «-/+» (17).
The symbol of the selected program will flash,
the display (3) will show the program settings set
by default.
Setting the «Multicook» program:
Touch the button (19), the flashing tempera-
ture indications as set by default will appear on
the display (3). Use the buttons (17) «-/+» to set
the necessary cooking temperature.
Touch the button (19)
–
(3) will show the flashing indications of cook-
ing time. Use the buttons (17) «-/+» to set the
necessary cooking time.
VT-4225.indd 7
4.
If you want to start cooking immediately, skip
this step.
on
The delayed start function allows to set the cook-
ing end time. See the list of programs with avail-
able delayed start function in the table «Cooking
programs».
Example:
If you set the delayed start time for 2:00, and dura-
tion of the selected program is 50 minutes, the
unit will stay in standby mode for 1 hour 10 min-
utes and then the cooking process will start.
–
–
–
–
–
5.
–
on the lid (8)
–
–
6.
–
–
again, the display
–
–
7
ENGLISH
Setting the delayed start
Select a cooking program and make the settings.
Touch the «DELAYED START» button (18), the
indicator will appear on the display, the
delayed start time in hours will be flashing.
Use the buttons (17) «-/+» to set the delayed
start time in hours.
Touch the «DELAYED START» button (18), the
minutes digits will be flashing.
Use the buttons (17) «-/+» to set the delayed
start time in minutes.
Starting the cooking program
To start the cooking program, touch the but-
ton (19) . If you have set the delayed start
function and switched the unit on, the unit will
be operating in standby mode, the symbol
« » will be shown on the display (3). Once
the delay time is over, the unit will be switched
on in the cooking mode, the symbol
out as well.
If after having selected and set the cooking
program, you do not switch the unit on with
the button (19) , then two minutes later you
will hear sound signals and the unit will auto-
matically go into sleep mode, the display (3)
will show the symbols "- - - -".
To switch the unit off while in the delayed start
mode or during cooking, touch the button (19)
for two seconds.
End of cooking and the keep warm func-
tion switching on
Sound signals will inform you that the cooking
program is finished.
If the keep warm function is available
for the selected program, the unit will be auto-
matically switched to the keep warm mode.
Symbol will appear on the display (3).
To switch the keep warm mode off, touch the
button (19) for two seconds.
After that unplug the unit.
will go
26.08.2014 14:22:12