Inhaltsverzeichnis
Werbung
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
gouge and cut grooves in the workpiece. If the grinder
is held at too sharp an angle, it will also gouge the
workpiece because of concentration of pressure on a
small area.
■ Use just enough pressure to keep the grinder from
chattering or bouncing.
NOTE: Heavy pressure will decrease the grinder's
speed and put a strain on the motor. Normally the
weight of the tool alone is adequate for most grinding
jobs. Use light pressure when grinding jagged edges or
loose bolts where there is the potential for the grinder
to snag on the metal edge.
■ Lift the grinder away from the workpiece before turning
off the grinder.
MAINTENANCE AND CLEANING
WARNING
When servicing, use only identical replacement parts.
Use of any other part could create a hazard or cause
product damage.
WARNING
Always wear eye protection. Failure to do so could
result in objects being thrown into your eyes resulting
in possible serious injury.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning, performing
any maintenance, or when storing the tool.
General Maintenance
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and can be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which could result
in serious personal injury.
Replacing The Guard
WARNING
Do not change or loosen guard screw. Failure to heed
this warning may cause the guard to become loose
during operation resulting in serious personal injury.
After extended use, the guard may wear and need
replacing. If you drop the grinder and damage the guard
it may also be necessary for you to replace it.
English (Original Instructions)
5
To replace the guard:
WARNING
To prevent loss of control and possible serious
personal injury, always operate the grinder with both
hands, keeping one hand on the side handle.
■ Remove the battery pack from the grinder.
■ Depress spindle lock and rotate clamp nut until spindle
locks.
■ Loosen and remove clamp nut from spindle using the
wrench provided.
■ Remove grinding wheel and disc flange.
■ Unlock the guard clasp by pulling the clasp out, away
from the grinder.
■ Open clasp fully and twist guard to release it from the
locking groove in the tool housing.
■ Remove guard.
■ Place the new guard on the shoulder of the bearing
cap.
■ Rotate guard to the correct position. Refer to
Positioning the Guard earlier in this manual.
NOTE: Be sure the raised ridge on the guard is
seated in the groove on the bearing cap.
■ Reassemble disc flange, grinding wheel, and clamp
nut. Refer to Installing Grinding Wheel earlier in this
manual.
■ Tighten the clamp nut securely with the wrench
provided.
Battery Pack Removal And Preparation For
Recycling
WARNING
Upon removal, cover the battery pack's terminals with
heavy-duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its
components. Batteries must be recycled or disposed
of properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit may
result. Keep away from children. Failure to comply
with these warnings could result in fire and/or serious
injury.
DISPOSAL
The machine, rechargeable batteries,
accessories and packaging should be sorted
for environmentalfriendly recycling.
Do not dispose of power tools and batteries/rechargeable
batteries into household waste!
ENVIROMENTAL PRORENCTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories and
packaging should be sorted for environmental-
friendly recycling.
Werbung
Inhaltsverzeichnis
