Vitek VT-2544 BK Betriebsanweisung Seite 5

•
Switch unit on by setting the switch (3) to the
position «ON», the indicator (2) will light up.
•
After finishing the unit operation, switch it off
by setting the switch (3) to the position «OFF».
Notes:
Always switch the unit off during the breaks
in operation.
When operating the unit from the mains,
switch the unit off and unplug the power
adapter before changing the attachments.
Hair cutting
Use the wide trimmers (9, 11) with correspond-
ing attachments (10, 12) for hair cutting.
You can use the detail trimmer (13) for cutting
designs on short hair.
•
Hair should be clean and dry during hair cut-
ting.
•
Install the required trimmer (9, 11 or 13).
•
Before cutting hair, switch the unit on, setting
the power switch (3) to the position «ON» and
make sure that unit operates normally and the
blades move smoothly. If there is too much oil
on the blades, remove the excessive oil with
a dry cloth.
•
Switch the unit off by setting the switch (3)
to the position «OFF», then install the corre-
sponding attachment (10 or 12) on the trim-
mer (9 or 11).
•
Seat the person so that his/her head is
approximately at your eye level, cover the
person's shoulders with a towel and set hair
with the comb.
•
Switch the unit on by setting the switch (3) to
the position «ON».
Reminder
Always cut off a little amount of hair at a
time; you can always return to the cut area
again for additional cutting.
The best haircutting results are reached on
dry hair, not wet.
Comb the hair to reveal uneven locks.
It is better to leave longer hair after cutting
for the first time.
After learning the unit better, you will learn
to arrange your hair in any style you need.
Shaving
The best shaving results are achieved if your
skin is dry.
Your skin may need 2-3 weeks to get used to this
shaving system.
VT-2544.indd 5
•
Install the shaving attachment (15).
•
Set the switch (3) to the «ON» position to
switch the shaver on.
•
Touching the skin slightly, move the shaver
back and forth and rotationally at a time.
•
After you finish shaving, switch the unit off
by setting the switch (3) to the «OFF» posi-
tion.
•
Clean the shaving attachment.
Cutting beard and mustache
Use the trimmers (9, 11) with the attachments
(10, 12) for beard styling; you can also use the
detail trimmer (13).
•
Install the trimmer (9 or 11) on the unit and
install the corresponding attachment (10 or
12) on the trimmer.
•
Until you learn your trimmer better, set the
hair length to 9 or 12 mm.
•
To cut the beard symmetrically, start cutting
from the ear to the chin on the one side of the
face, and then repeat the beard cutting on
the other side.
•
Comb the mustache and then cut it from the
middle to the corners of the lips.
Note: Always cut off a little amount of hair at
a time – you can always return to the cut area
again for additional trimming.
•
Finishing the beard cutting, remove the
attachment, turn the blades of the unit
towards yourself and define the desired
shape. Do not press on the unit strongly,
there is danger of injuries or cuts when open
blades come in contact with the skin.
•
When cutting hair on the cheeks, move the
trimmer downwards; move it upwards in the
neck area.
•
Regularly cut the beard and mustache to
keep their shape.
Nose and ears trimmer
Be careful when using the trimmer (14) for cut-
ting hair in the ears and nose. Insert only the
metal tip of the trimmer attachment into the auri-
cle or the nostril.
•
Install the attachment (14) on the unit body
and check if it is set securely.
•
Switch the unit on by setting the switch (3) to
the position «ON».
•
Move the metal tip of the trimmer smoothly
back and forth and rotationally; carefully cut
hair in the nose and/or ears.
5
ENGLISH
09.01.2014 10:30:27