Vitek VT-2544 BK Betriebsanweisung Seite 4

ENGLISH
unit works improperly or after the unit was
dropped.
•
Do not disassemble the unit by yourself, if any
malfunction is detected or after the unit was
dropped, apply to the nearest authorized ser-
vice center.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
USING THE TRIMMER
After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
Battery charging
Full charging of the battery provides about
45 minutes of continuous unit operation.
•
Insert the connector of the power adapter (6)
into the socket (1) on the unit body or into the
socket on the rear side of the base (5).
•
If you are using the base (5), set it on a flat
stable surface and then put the trimmer on
the base.
•
Plug the power adapter into the mains socket,
the indicator (2) will light up red.
•
Before the first usage of the unit, charge the
battery for 8 hours. Further full recharging
cycles are also no less than 8 hours.
•
After charging remove the power adapter (6)
from the mains socket and disconnect the
adapter cord from the base (5) or from the
trimmer body.
Notes:
Recharge the battery only after its complete
discharge.
Charge the battery at the temperature from
+5° C to +35° C.
Never leave the unit connected to the mains
unattended.
After a long period of not using the unit
(more than 2 months), charge the battery
completely before using the unit.
On/charging indicator (2)
The indicator (2) glows red during charging;
the indicator (2) glows green if the unit is on
and operates from the battery; the indicator (2)
VT-2544.indd 4
glows orange if you operate the unit connected
to the mains.
Trimmers
•
Before installing and changing the attach-
ments, switch the unit off by setting the
switch (3) to the position «OFF»; if the unit
is powered by the power adapter, unplug it.
•
To install any trimmer (9, 11, 13, 14 or 15)
on the unit body, insert the lock on the bot-
tom part of the attachment into the notch on
the rear side of the unit body and then press
on the upper part of the attachment until fix-
ing (pic. 1).
•
To remove the trimmer, press it from the side
of the blades (pic. 2).
Installing the adjustable attachment
for 30 mm trimmer
•
Install the trimmer (9) on the unit body.
•
Insert the trimmer (9) into the notches of the
adjustable attachment (10) (pic. 3). Adjust
the cutting length (3, 4, 5, 6 or 7 mm) by mov-
ing the attachment (10) relative to the trim-
mer (pic. 4).
•
To remove the attachment (10), move it in the
direction of the arrow «PUSH».
Attachments for 40 mm trimmer
•
Install the trimmer (11) on the unit body.
•
Install the upper part of the attachment (12)
on the trimmer (11) and then fix the bottom
part of the attachment (12) (pic. 5).
•
To remove the attachment (12), pull the lock
on its bottom part (pic. 6).
Lubricating oil
•
To maintain the unit in a good condition, you
should lubricate the trimmer blades (9, 11,
13) after every use of the unit.
•
For lubricating the blades, use only the lubri-
cating oil (8), supplied with the unit.
•
The trimmer for nose and ears (14) doesn't
require lubricating.
Using the unit
•
For cordless use of the unit, charge the bat-
tery fully.
•
Install the required trimmer and attachment.
Note: For corded operation, connect the power
adapter (6) cord to the socket (1) and plug the
power adapter into the mains.
4
09.01.2014 10:30:27