Whirlpool AWG 1112 /PRO Kurzanleitung Seite 3

4.
SWITCH ON THE WASHING MACHINE
• Press the "On/Off" button until the programme button
lights up. An animation appears on the control panel and
the appliance plays a sound. The washing machine is then
ready for operation.
5.
SET THE DESIRED PROGRAMME
GUIDED MODE — the button light will guide you through setting
your programme in the following order: Selection of programme/
temperature/spin speed/options. As soon as you confirm a selection
by pressing the knob, the button light jumps to the next step.
• Select programme:
Make sure that the programme button lights up.
Turn the knob to select the desired programme.
The indicator next to the selected programme lights up.
Confirm the desired programme by pressing the knob.
• Change temperature, if required
If you want to change the temperature indicated on the
display, make sure that the Temperature button lights up.
Turn the knob to select the desired temperature, then press
the knob to confirm.
• Change spin speed, if required
If you want to change the spin speed indicated on the
display, make sure that the Spin button lights up.
Turn the knob to select the desired spin speed, or Rinse
hold, then press the knob to confirm.
Refer to OPTIONS, FUNCTIONS AND INDICATORS for more
information.
• Select options, if required
If you want to select additional options, make sure that the
Options button lights up. The options which are selectable
for your programme are indicated by the arrows which are lit
up .
Turn the knob to select the desired options. The symbol for the
selected option will flash. Press the knob to confirm.
Some options/functions can be selected by pressing the button
directly:
Refer to the OPTIONS, FUNCTIONS AND INDICATORS section for
more information.
INDIVIDUAL MODE
After you have switched on the washing machine, you are not
forced to follow the GUIDED MODE.
The order in which you choose to set your programme is up to you.
To make a setting, first press the relevant button, then turn the knob
to select, and finally press the knob to confirm.
The range of temperatures, spin speeds and options depend on the
programme selected. It is therefore recommended that you start by
selecting the programme.
6.
ADD DETERGENT
• If you are not using the Dosing Aid function, pull out the
detergent dispenser and add detergent (and additives/
softener) now; observe the dosing recommendations on
the detergent pack.
If you have selected PREWASH or START DELAY, observe the
recommendations in the OPTIONS, FUNCTIONS AND INDICATORS
section. Then carefully close the detergent dispenser.
• If you are using the "Dosing Aid" function, add detergent later,
after you have started the programme. Refer to the OPTIONS,
FUNCTIONS AND INDICATORS section for more information.
• After having added detergent/additives, do not open the
detergent dispenser to avoid any overflow.
7.
START PROGRAMME
• Press and hold "Start/Pause" until the button lights up and
stays on; the programme will start.
• If you have selected "Dosing Aid", the washing machine
indicates the recommended detergent amount for your laundry
load after the programme starts.
Follow the instructions as indicated in the OPTIONS, FUNCTIONS
AND INDICATORS/Dosing Aid section.
8.
CHANGE THE SETTINGS OF A PROGRAMME WHICH IS
RUNNING, IF REQUIRED
You can still change the settings while a programme is running.
The changes will be applied, provided the respective programme
phase has not yet finished.
• Press the relevant button (for example the "Spin speed" button to
change the spin speed). The selected value will flash for a few
seconds.
• While it is flashing, you can adjust the setting by turning the knob.
If the value stops flashing before you have adjusted it, press the
button again.
• Press the knob to confirm the new setting. If you do not confirm it,
the new setting will be confirmed automatically: It will stop
flashing.
The programme will continue automatically.
To change the settings of a programme which is running, you can
also:
• Press "Start/Pause" to pause the programme which is running.
• Change the settings as desired.
• Press "Start/Pause" again to continue the programme.
9.
PAUSE A PROGRAMME WHICH IS RUNNING AND OPEN
THE DOOR, IF REQUIRED
• Press and hold "Start/Pause" to pause a programme which
is running.
• Provided the water level and/or temperature is/are not
too high, the door open indicator lights up. You can
open the door, for example to add/remove laundry.
• Press "Start/Pause" to continue the programme.
EN
3