Inhaltsverzeichnis
Werbung
5 - Having taken this 4 fundamental precautions, place the foods in your freezer, preferably near to the freezer walls and
under the load level impressed in the interior wall.
3 - MAINTENANCE
Before any maintenance operation, disconnect the plug from the mains supply.
1 Remove the ice that grows on the freezer walls - with the appropriate spade that is supplied with the freezer walls. You
should never let the ice grow more than 5 mm thick.
Please Note!
When you need to remove ice from the rear wall of model BETA 200, use the manual defrosting system that
is fitted. For the purpose, press the button
minutes, then use the scraper to remove the accumulated ice.
Warning! This option is available only on the CEP TOPO and BETA 200 model.
2 If you wish to replace any lightening components, remove the acrylic covering over the lightbulb being replaced. Turn
the lightbulb by a 90º angle and pull it downwards until it becomes loose. Always verify that you replace it with a 13W
lightbulb.
3 For maintenance of the refrigerator group or the electrical equipment remove the front grid and open the drawer so
access to all components is easy.
3.1 Condenser blades should be cleaned at time intervals that should be established by
yourself according to equipment installation location cleanliness.
A non-metallic brush or low pressure air should be used for this cleaning operation. Air
suction occurring at the condenser blades results in dust deposition, which can cause
serious malfunction and/or loss of equipment efficiency.
WARNING!
If you intend to clean the exterior of the appliance, this should never be done directly with water. The
presence of water or moisture on the electric circuit may seriously damage your appliance.
VERY IMPORTANT!
this rule may cause serious faults.
In closing, we would like to leave a word of advice. Never switch the freezer off when it contains products the
factory-programmed electronic controller ensures that the products are kept in good condition, as
economically as possible.
Class 3 Equipment: Electrical safety tests performed at an operating room temperature of 32ºC
WARNING! This appliance was not designed for use by people (including children) with reduced physical or
mental capacity, or people with a lack of experience or knowledge, unless they have received training or
instruction on the use of the appliance from a person responsible for its safety. Children should be supervised
to ensure that they do not play with the appliance.
INSTRUCCIONES PARA LA INSTALACIÓN Y UTILIZACIÓN
ES
1 - INSTALACIÓN DE SU CONGELADOR
I
NSTRUCCIONES PARALAINSTALACIÓN Y UTILIZACIÓN
1 - INSTALACIÓN DE SU CONGELADOR
En el momento de instalar su nuevo congelador, usted debe tener en cuenta las seguintes precauciones:
1 - El suelo debera ser absolutamiente llano, para que los quatro piés se apoyen a la perfección.
2 - El congelador deve ser posicionado de manera a assegurar el acesso facil e rapido a la enchufe.
3 - Es condición fundamental para el buen funcionamiento del aparato que este sea instalado en un local con buena
circulación d'aire y fuera de la incidencia de los rayos solares o de qualquier fuente de calor. La distancia del aparato a las
paredes o muebles mas proximos debe ser de 15 cm, como minimo.
4 - El congelador que acaba de comprar debe, en parte, su bueno funcionamiento a la ventilación forzada con que se halla
equipado. Sin embargo, la existencia de elementos que eventualmiente puedan obstruir la circulación del aire - através de
la rejilla trasera - podria comprometer la normal eficácia de su congelador.
5 - La conexión al enchufe de corriente elétrica solo deberá hacerse si:
- La tension instalada en su casa sea la misma que la indicada en la placa de características.
- El enchufe de su instalación se halle conectada a la tierra.
En caso de duda consulte su electrecista.
2 - UTILIZACIÓN DE SU CONGELADOR
2.1 - MANEJO DEL CUADRO DE MANDOS
El cuadro de mandos se halla situado en la parte inferior derecha y frontal de su congelador.
Observelo con atención y verá:
1 Interruptor de 2 posiciones,
1 controlador electrónico de temperatura, cuya función es controlar la temperatura media interior de su aparato. Si desea
cambiar la temperatura media interior de funcionamiento de su aparato, siga los siguientes pasos:
Desbloquee el teclado, pulsando al mismo tiempo las teclas
A continuación pulse la tecla
modificar la temperatura media interior de su aparato aumentando o disminuyendo los valores utilizando
of the controller during 3 seconds, until the LED (2) lights up. Wait for 10
When cleaning the floor, take care not to spill water on the appliance. Failure to observe
/
cuya la función es ligar e desligar la iluminación interior.
(
)
SET
hasta que el led
ºC (3)
y
hasta ver la palabra
comeze a parpadear en el visor. En este momento puede
2.
on
en el visor.
4
Werbung
Inhaltsverzeichnis
