Cleaning And Maintance - MaxPro PROFESSIONAL MPES500V Bedienungsanleitung

OPERATING INSTRUCTION
VARIABLE SPEED CONTROLLED TRIGGER SWITCH（Fig.1）
Turn the knob to "+" means increase the speed and to "-" means decrease the speed.（Fig.1）
LOCK-ON" BUTTON（Fig.2）
without holding the trigger.
TO UNLOCK THE TRIGGER: squeeze trigger（5）
CAUTION！
REVERSING SWITCH LEVER （Fig.3）
The reversing switch lever（4）
bit.
bit move the lever（4）
CAUTION！
LEVEL BUBBLE （1 ）
The tool is equipped with a level bubble（1） that allows you to conveniently find the angle you need
when you use the machine. This feature will allow you to finish your work more precisely.
DEPTH ADJUSTMENT（Fig.4）(Fig.5)
1.The depth can be adjusted by turning the locking sleeve（7）. The locking sleeve（7）is connected with
（6）
locking sleeve（7）.
2.Adjust the locking sleeve（7）
REPLACING BIT TIPS AND BIT TIP HOLDERS
1.Hold the locking sleeve（7）
PLIERS.）
2.If you find the locking sleeve（7）
（DO NOT USE PLIERS ON NOSE PIECE.）
ELECTRIC SCREWDRIVER OPERATION
2.Press the screw point against the drywall with steady even pressure. At this point, the clutch will engage,
second.

CLEANING AND MAINTANCE

ADD OIL IN IT OF TEN. The drill is a speed working tool. The lubrica
grease in r case and bearing must o en be kept clean and add or change it any
CHECKING AND MATNTENANCEONITFREQUENTLY. The drill should be checked, repaired day to day and
5
（2） and release trigger（5）.
（4）
（4） is the "Lock-OFF"
（DO NOT USE
rease is volatlilized easily so the
GB
see whether the power wire, the plug and the switch work well or not. Pay a en
as whether the insula
well contacted, the armature winding and the stator winding are in short circuit or broken circuit, and the
bearing, the other moving parts are damaged, etc.
（3） .
EACH PART SHOULD BE WELL KEPT AND WHEN YOU WANT TO CHANGE THE PART. USING THE SAME ONES
When the drill needs taking apart and checking, do keep each part including insula
If they are damaged you must change the new one and the same one. Be sure not to use the subs
materials which is worse than one ne used and the part which does not agree with the standard. When
fixing, you must put the parts in their pr
BE CAREFUL OF THE INSULATION RESISTANC The drill not be used for long or to have been used in damp
（2） .
c st be tested in its vinding of the insula
winding and iron center is less than 2 milion ohms, you must drying treatment to the winding un
than 2 milion ohms. STORED CARETULLY The drill should be kept in a dry clean place and without any
corrosive gases.
ENVIRONMENT
Do not dispose of electric tools, accessories and packaging together with household waste material -
in observance of European Dir
implementa
be collected separately and returned to an environmentally compa
TROUBLE SHOOTING
Fault Symptom
Out of service at switch-on
Excessive sparkling
Drilling speed drop
Machine superhea
resistance works normally, the handle is flexible, the inverter and brushes are
resistance with a 500 milion ohm meter. If the
ve 2002/96/EC on waste of electric and electronic equipment and its
cordance with na aw, electric tools that have reached the end of their life must
Possible Cause
Shortcircuit in motor winding
Disc etween plug and
power socket
No voltage in supply socket
Loose switching contact
Disc etween carbon
brush and commutator
Underpressure in carbon brush
spring
Excessive wearout of carbon brush Replace carbon brush by reparier
Ring fire caused by shortcircuit in
rotor winding shortcircuit
Ring fire caused by shortcircuit in
commutator segment
Low supply voltage
Damage in machinery parts
Shortcircuit in rotor
Blcokup at drilling bit during
drilling metallized product
Electromotor overload
Unsmooth air outlet
GB
to everything such
r and casing pipe.
ny of them.
re
recycling facility.
Tr
Replace stator/rotor by repairer
Put plug in power socket
Check and repair power supply
Replace switchboard by repairer
Check c etween carbon
brush and commutator by repairer
Replace carbon brush by reparier
Check or replace rotor by repairer
Check or replace rotor by repairer
Regulate supply voltage
Replace machinery parts by repairer
Check or replace rotor by repairer
Stop drilling
Normally operate with reference to
specifica
Clear up air intake/outlet
6