Safety Instruction - MaxPro PROFESSIONAL MPES500V Bedienungsanleitung

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from
moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the
power source and/or the battery pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tool's operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTION

• Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them
before you start working
• Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool
• Maxpro can assure flawless functioning of the tool only when original accessories are used
• Use only accessories with an allowable speed matching at least the highest no-load speed of the tool
• This tool should not be used by people under the age of 16 years
• Use completely unrolled and safe extension cords with a capacity of 16 Amps (U.K. 13 Amps)
• Always keep the cord away from moving parts of the tool
• If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect
the plug
• Never use the tool when cord is damaged; have it replaced by a qualified person
• If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately
switch off the tool
• In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug
• Secure the work piece (a work piece clamped with clamping devices or in a vice is held more securely
than by hand)
3
GB
• Hold the power tool only by the insulated gripping surfaces when performing an opera
accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make
exposed metal parts of the power tool "live" and shock the operator)
• Use suitable detectors to find hidden
with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion;
penetra water pipe will cause property damage or an electrical shock)
• Do not work materials containing asbestos (asbestos is considered carcinogenic)
• Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful
(contact with or inhala of the dust may cause allergic rea
operator or bystanders); wear a dust mask and work with a dust extr
• Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in c
with addi ves for wood condi g; wear a dust mask and work with a dust extrac
connectable
• Follow the dust-related na requirements for the materials you want to work with
• When you put away the tool, switch off the motor and ensure that all moving parts have come to a
complete stands
• Always disconnect plug from power source before making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not le
una ended
• Support the tool so that steady, even pressure is applied to the screw driving bit. Operate the trigger
switch by depressing with one or two fingers.
• Place a electric screw on the bit. The magnetic bit holder will hold any steel electric screw without any
additional assistance.
• When properly set, the screw head should pull into the drywall paper without cracking or tearing the
paper, then release slightly below flush with the drywall board. In this manner, minimum work is left when
spackling screw heads and taping the seams.
•
If it becomes necessary to remove the screw, remove the snap off nose piece, reverse the direction of
rotation (when the motor is in the "OFF" position.) Place the bit tip into the screw, switch tool "ON" and
apply pressure to engage the clutch. Replace nose piece by pushing and slightly twisting to seat into the
depth gauge. Set lever back to forward while the trigger switch is in the "OFF" position.
SYMBOLS
Read the manual
Warning
lines or call the local company for assistance (contact
s and/or respiratory diseases to the
evice when connectable
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
GB
where the
device when
4