Nilox J27-GOHD Bedienungsanleitung Seite 3

2. Operating Introduction for Mini 3.5mm wireless audio adapter
1) Charging: Rechargeable Li-ion battery, USB interface in computer or DC
5V/500mAcharger. Connect USB cable to the Mini 3.5mm wireless audio adapter,
and connect the USB cable to charging source, the red LED light is displayed during
charging. When the battery is fully charged, the red indicator light turns off.
2) To switch on: Long press"on/off" until blue LED brighten, then release the but-
ton.The power successful on. Mini 3.5mm wireless audio adapter has enter into
stand-by state,blue light flash,after successfully paring with headset, the blue light
will steadily displayed .
3) To switch off: Under the power on state, long press"on/off" button untill the
blue LED light turnsoff, the Mini 3.5mm wireless audio adapter will power off.
4) Automatically power off: If the USB cable didn't connect the launcher to com-
puter, there is no power supply to launcher,under this state, when the headset
hasn't successfully paired with Mini 3.5mm wireless audio adapter, the adapter will
automatically power off after 3 minutes.
5) Connect Mini 3.5mm wireless audio adapter to audio equipments:
The function of Mini 3.5mm wireless audio adapter is to transfer the audio signal
from audio equipments to headset over radio wave transmission, there are two
connection ways:
A. USB access mode: This mode is for computer and other equipments which have
USB audio output/input function.
After connect launcher to computer with USB cable, the launcher will automati-
cally turns on. The computer will automatically distinguish and set up driver pro-
cedure, when the words "New hardware installment and may use" appear in the
lower right corner means launcher installation finished. (After this, it can be plug
and play ). At this time, it can be wireless connect with headset, you can enjoy the
music from computer or make remote voice call via internet.
B. 3.5mm audio access mode: This mode is for 3.5mm audio output jack equipment,
such as MP3, MP4, iPod etc.
Insert the 3.5mm audio input connector in the launcher into 3.5mm audio output
jack, and pairing with wireless headset, then can enjoy the music playing from audio
output equipments wirelessly.
Remark: This mode can only listen but can not remote communication via internet.
2
5 Key directions (Headset)
1. Product structure
2. Operating Introduction for Headset:
1) Charging:The headset uses Li-ion rechargeable battery. Charge power is com-
puter USB port, or DC 5V/500mA charger.
Connecting the USB-DC charging cable with the charging power, then the headset
can be charged.While charging,the green light will bright,after fully charged,the
green light will disappear.
2) Power on:Shortly press the "On/Off" buttom,the red indicator light on the
headset will flash.After successfully connect with Mini 3.5mm general audio inter-
face launcher, the red indicator light will steadily brighten..
3) Play/Pause:Shortly press "Play/Pause" buttom, the music can be played or pause.
(When using 3.5mm audio access mode, this button can't work)
4) Volume adjusting: Shortly press "Volume+" or "Volume-" to adjust the
volume,long time press for continuously adjusts.
5) Select previous or next songs:Shortly press "Previous" or "Next " buttom to
play previous or next song.(When using 3.5mm audio access mode, this botton
can't work)
6) Power-saving sleep mode: Failed in looking for the pairing device in three min-
utes ,the headset will automatically enter into power-saving sleep state.( Red light
slowly flash)
7) Wake-up: Shortly press" On/Off"to power off and press repeatedly to turn on,
the headset can wake-up from sleep mode.
8) Turn-off headset: Under the power on state, shortly press"On/Off" to turn off
headset, and the red indicator light will turn off.
3