How To Use; Specifications - SYNQ AUDIO RESEARCH DIGIT 1KO Bedienungsanleitung

ENGLISH
13. 30Hz LOW CUT FILTER: eliminates unwanted subsonic frequencies under 30Hz. In most cases these
frequencies only consume a lot of energy without any added value to the music.
14. OPERATION MODE switch: Used to set the operation mode of the amplifier. The most common
operation mode is "stereo". If you need more power, you can operate the amplifier in bridge mode. In
mono mode you only have to connect the left input to drive both outputs. Refer also to n° 3 for more
information.
15. INPUT SENSITIVITY SWITCH: you can choose 3 different input levels: 26 dB / 32 dB / 1,4 V
16. BALANCED XLR OUTPUTS: Can be used to send the signal to the next amplifier. Pin1: signal ground,
Pin2: signal+, Pin3: signal -
17. BALANCED XLR INPUTS: Pin1: signal ground, Pin2: signal+, Pin3: signal –

HOW TO USE

STEREO OPERATION:
 Connect the audio signal to the inputs (15 or 16)
 Set the operation mode switch (13) to "stereo"
 Connect the matching speakers to the L+R Speakon
 Make sure the mains voltage matches 230Vac before connecting the
mains cable to the earthed wall socket.
 Set both input gains (2) to zero
 Make sure there's a music signal at the input
 Turn the amplifier on (8)
 Adjust the input gains (2) to the desired level
BRIDGE OPERATION:
 Connect the audio signal to the left input (15 or 16)
 Set the operation mode switch (13) to "bridge"
 Connect the matching speaker(s) to the Bridge output (12)
 Make sure the mains voltage matches 230Vac before connecting the
mains cable to the earthed wall socket
 Set both input gains (2) to zero
 Make sure there's a music signal at the left input
 Turn the amplifier on (8)
 Adjust the left input gain (2) to the desired level, leave the right channel
gain to zero.
MONO OPERATION:
 Connect the audio signal to the input of the left channel (15 or 16)
 Set the operation mode switch (13) to "mono"
 Connect the matching speakers to the L+R Speakon
 Make sure the mains voltage matches 230Vac before connecting the
mains cable to the earthed wall socket
 Set both input gains (2) to zero
 Make sure there's a music signal at the input
 Turn the amplifier on (8)
 Adjust the left input gain (2) to the desired level, leave the right channel
gain to zero.
SYNQ
®
OPERATION MANUAL
®
outputs (11)
®
outputs (11)
5/36 DIGIT amplifiers
ENGLISH

SPECIFICATIONS

Digit-1K0
Power stereo 8Ω
2x 300Wrms
(1kHz, THD+N<0,1%)
Power stereo 4Ω 2x 540Wrms
(1kHz, THD+N<0,1%)
Power bridge 8Ω 1x 1080Wrms
(1kHz, THD+N<0,1%)
Power mono 8Ω 2x 300Wrms
(1kHz, THD+N<0,1%)
Power mono 4Ω 2x 540Wrms
(1kHz, THD+N<0,1%)
Power efficiency
>90%
Freq. Resp. 5 – 36.000Hz
(+/-1dB)
Input Sensitivity 26 dB / 32 dB / 1,4 V
Input impedance unbalanced 10 kΩ
Input impedance balanced 20 kΩ
S/R ratio >100dB
(A-Weighted)
Damping factor (5Hz-1kHz) 280
Slew Rate 29V/uS
Cooling variable speed fan
Signal inputs Balanced XLR
Signal outputs
Balanced XLR
Power supply AC85-270V / 50-60Hz
Power consumption (max peak) 1200 Watt
Dimensions (WxHxD mm) 482x44x215 (19"/1U)
Weight (kg) 3,3kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
SYNQ
®
OPERATION MANUAL
Digit-2K2 Digit-3K6
2x 650Wrms 2x 1050Wrms
2x 1100Wrms 2x 1800Wrms
1x 2200Wrms 1x 3600Wrms
2x 650Wrms 2x 1050Wrms
2x 1100Wrms 2x 1800Wrms
>90% >90%
5 – 36.000Hz 5 – 36.000Hz
26 dB / 32 dB / 1,4 V 26 dB / 32 dB / 1,4 V
10 kΩ 10 kΩ
20 kΩ 20 kΩ
>100dB >100dB
280 280
29V/uS 29V/uS
variable speed fan variable speed fan
Balanced XLR Balanced XLR
Balanced XLR Balanced XLR
AC230V / 50Hz AC230V / 50Hz
3200 Watt 3900 Watt
482x44x301 (19"/1U) 482x44x301 (19"/1U)
5,5kg 5,6kg
6/36 DIGIT amplifiers