General Precautions - Ideal Standard MOMENTS Installations- Betriebs Und Wartungshandbuch

G P
ENERAL RECAUTIONS
ATTENTION!
PRECAUTION FOR USE OF THE TUB
- For proper maintenance of the shell of the tub, fill it with mixed-
temperature water and not with hot water followed by cold
water.
- Do not use electrical devices while bathing.
- Do not place incandescent objects in the shower box, such as
cigarette butts, hair dryers, flashlights, lamps, and so on.
- When cleaning the shower box do not use acetone, solvents,
powder detergents or abrasive cloths.
- Detergents other than those recommended by the manufacturer
may damage the whirlpool product.
- When the unit is in standby mode, it consumes a certain amount
of energy. It is advisable to disconnect the unit from the power
supply by placing the differential switch upstream from the
system in the "0" position.
- We also suggest periodically testing the operation of the differen-
tial switch by pressing the "TEST" button.
- The unit is not intended for individuals (including children) of limited
sensorial, physical or mental capacities, or who do not have the suf-
ficient experience or knowledge, unless a person who is responsible
for their safety has instructed them on the use of the machine.
- Children must be kept from playing with the unit.
P
RECAUTIONS FOR USE OF ESSENTIAL OILS
- Immerge solid additives with a fine-mesh net or with a special
filter. Ensure that they do not contain alcohol or other solvents
which may damage the system.
- Avoid using mixtures with Dead Sea salts.
T
UB OPERATION
- Place the omnipolar switch in the "I" position.
- The LED of the O/I button comes on steady red to indicate
that the unit is powered.
- By pressing the O/I button to switch the tub on, the LED
becomes steady green and the light comes on at the same time.
- To switch the light off, press the O/I
- When you have finished use, switch the omnipolar switch back to
position "O".
Phase
Stand-by
Light operation
8
TT0288264_00_Moments.indd 8
M
AINTENANCE
ROUTINE MAINTENANCE
Lime and overly aggressive detergents may over time make the surfaces
of the tub opaque, but with simple polishing it is possible to restore
the original brilliance of the material:
- Put some automobile polishing compound on a soft cloth.
- Rub the surface with a circular movement, pressing fairly hard.
- Complete the operation by wiping with a clean cloth.
For ordinary cleaning of the bath surfaces, only use detergents recom-
mended by the Manufacturer; the use of unsuitable detergents may
damage the bath surfaces and operating system.
- Never use powder detergents.
Liquid detergents may be used if they are free of alcoholic sub-
stances.
- Never use products such as ammonia, acetone, alcohol and the
like because they may permanently damage the tub.
You can contact one of our service centres to purchase a series of
products which are suitable for the cleaning and maintenance of your
whirlpool tub.
SPECIAL MAINTENANCE
Scratches, deep cuts and even surface cigarette burns can be removed,
thus restoring the original appearance of the tub, by performing the
following actions.
Damage must be evaluated for its severity and repairs must be carried
out in steps:
I. If the scratch or damage is particularly deep (<0.5mm), start
by sanding the zone when dry (work on a larger surface than
the damaged area in order to avoid unsightly dips), using 400
sandpaper wrapped around a polystyrene block, moving it with a
circular motion.
II. For less serious damage, the dry repairs can be started using
600/800 sandpaper.
movement, using 1000 sandpaper dampened with water.
using slight pressure.
This work must be performed delicately and gradually so as not to
remove too much material from the thickness of the tub, thus causing
damage.
Note:all of the previously mentioned maintenance is to be consi-
button again.
dered as valid only for surfaces which were originally glossy. For
opaque surfaces, evaluate the type of intervention based on the
severity of the damage.
G
Led
UARANTEE
The manufacturer guarantees that this product has been manufactured
Lit red
with top quality materials and components, and that it has undergone
those tests required by the manufacturer's approval standards and by
Lit green
current national and European standards.
This guarantee, for the period contemplated by law, covers only
those defects (appearance, dimension, operation) which are due to
manufacturing errors, and which are verified and confirmed by the
manufacturer's after-sales service technical staff.
THE GUARANTEE TAKES EFFECT AS OF THE PURCHASE DATE OF THE
PRODUCT, AS SHOWN ON THE INVOICE OR RECEIPT.
16-11-2010 11:50:07