Getting Started - DOMENA SC120 Bedienungsanleitung

GETTING STARTED

1. Attaching accessories
•
Connect the steam hose as far as the base of the appliance.
•
Attach the accessories to the pistol handle or one or two extension tubes.
•
With the big rectangular brush, insert the curved connector.
2. Filling the water tank
•
Suitable water: tap water, demineralised water or distilled bottled water.
•
Always use clear, pure water.
•
To ensure the long-life of your appliance, we recommend that you mix tap water and non-perfu-
med demineralised water (50:50).
•
NEVER use pure demineralised water, water collected from a tumble drier or water softener or
rain water.
Note: Switch off your appliance before filling the water tank in its compartment.
•
Release the small water tank button
•
Use the filling beaker to fill the water tank. Do not exceed the "MAX" level indicated on the water
tank.
•
Replace the small water tank button in its original position.
Note: You can also remove the water tank from its compartment to fill it. In this case, check that
the water tank is properly in position afterwards by pushing it firmly into its compartment.
3. Getting started
•
Plug the appliance into an earthed socket
•
Press the ON button No. 5.
•
The pressure indicator light No. 4 is illuminated.
•
The appliance is ready to emit steam when this indicator light changes colour:
•
It changes from red to green.
•
Remove the steam safety lock No. 13 by placing it in the ON position.
•
Steam cannot be emitted when the safety lock is in the OFF position.
•
Steam can be emitted when it is in the ON position.
•
When you have finished using the appliance, check that the safety lock is in the OFF position to
avoid any accidental emission of steam.
Safety lock
•
Press the steam On/Off button No. 12 positioned on the pistol handle to generate steam.
Note: After use, press the steam button for a few seconds to remove any residual condensation
water in the main hose.
24
Warning!
Your steam cleaner is equipped with an anti-spill safety mechanism. This is activated when the
appliance is inclined at over 45° or falls onto the floor. In both cases, the power on indicator light
flashes and the device will immediately stop heating up and generating steam. When the appliance
is returned to its normal position (45° or less), it starts to heat up and release steam again.
4. Cleaning
•
Before cleaning a delicate surface (carpet, fabric, etc.), test the appliance on a hidden surface.
Wait for the steam to take effect and check that there is no colour change or deformity.
Using the accessories:
•
The rectangular brush is suitable for large surface areas (floors). Use it with the cloth.
•
The concentrated jet nozzle can be used with or without the extension tubes. The concentrated
steam jet increases the cleaning power to remove any encrusted dirt.
•
The round nylon brush connects to the concentrated jet nozzle. It is suitable for cleaning small,
very soiled surfaces and bathrooms.
•
The round copper brush connects to the concentrated jet nozzle. It has an abrasive action and is
suitable for DIY work.
•
The small curved nozzle is particularly suitable for cleaning small areas that are difficult to access
(radiator, etc.)
•
The fabric furnishings brush is fitted with the cloth, with or without extension tubes, and can be
used to remove dust from textile surfaces (sofas and cushions, etc.)
•
The window wiper connects to the fabric brush.
Note: On cold windows, pre-heat the surface initially by spraying the steam thirty centimetres
away from the glass.
5. Filling the water tank during use
The light (4) flashes when the water tank is not sufficiently full.
Fill the water tank as shown in 2.
6. Switch off the device
Place the On/Off button (5) in the Off position.
Unplug from the electric socket, leave the appliance to cool and put away.
The water tank should always be emptied after use in order to prevent the formation of deposits.
25
EN