Cotech DT8800IP44-5M Bedienungsanleitung

Flexible RGB LED Strip
Art.no 36-6703 Model DT8800IP44-5M
Please read the entire instruction manual before using the product
and then save it for future reference. We reserve the right for
any errors in text or images and any necessary changes made
to technical data. In the event of technical problems or other
queries, please contact our Customer Services.
Safety
• The product should only be connected to a 230 V AC,
50 Hz electrical outlet.
• Never immerse the product in water or other liquid.
• Do not place the product where there is a risk of it falling
into water or other types of liquid.
• The product may only be used with the supplied mains adaptor.
• The product must not be changed or modified in any way.
• Never hang anything on the product.
• Do not look directly into the light source as there is a risk
for eye damage.
• Never attempt to interconnect the product with other light strips.
• Make sure that the power adaptor is not pinched or
damaged in any other way during use.
• Never use the product if it, its power adaptor or plug are
damaged in any way.
• Never let children play with the product.
Operating instructions
1. The light strip can be
cut to a desired length.
Note: Cut only where
marked as shown in
the figure.
2. Use the included adhesive
to glue the protective
cover over the open
end of the light strip.
Let the adhesive cure for
at least 12 hours before
subjecting it to load.
GREAT BRITAIN • CUSTOMER SERVICE tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk
postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
3. Connect the LED strip to the power adaptor according to
the figure (the arrow in the picture shows the IR receiver for
the remote control).
4. Hang up the strip with the included cable clips. Be careful
not to damage the cable or mounting surface during
hanging.
5. Plug the mains adaptor into an electrical outlet.
Remote control
Pull the plastic film tab away from the battery compartment in
order to activate the battery.
1. Press repeatedly to increase
the brightness of solid
colours. Increase the speed
of colour transitions in
the following modes:
FLASH, STROBE, FADE and
SMOOTH.
2. Press repeatedly to decrease
the brightness of solid
colours. Decrease the speed
of colour transitions in
the following modes:
FLASH, STROBE, FADE and
SMOOTH.
3. [ ON/OFF ] Power switch
4. [ R, G, B, W ] Solid colour selections
5. [ FLASH ], [ STROBE ], [ FADE ], [ SMOOTH ] Light modes with
7 colours which transition quickly, slowly, smoothly, etc.
Care and maintenance
• Unplug the power adaptor from the wall socket before
wiping it clean with a dry cloth.
• If the power adaptor is not to be used for an extended
period, it should be unplugged and stored in a dry location
out of reach of children.
Changing the remote control batteries
1. Follow the illustration on the back of the remote control.
2. Press in the battery compartment's latch and slide it to
release and pull the battery holder from the compartment.
3. Insert a new battery into the battery holder. Make sure that
the positive (+) terminal is facing upwards, towards you.
4. Reinsert the battery holder back into the remote control.
Responsible disposal
This symbol indicates that this product should not
be disposed of with general household waste.
This applies throughout the entire EU. In order to
prevent any harm to the environment or health
hazards caused by incorrect waste disposal,
the product must be handed in for recycling so
that the material can be disposed of in a responsible manner.
When recycling your product, take it to your local collection
facility or contact the place of purchase. They will ensure that
the product is disposed of in an environmentally sound manner.
1 2 3
Specifications
Note: With the exception of the remote control, the product
4
itself has an IP44 rating.
• LED strip with RGB controller, designed to be powered
from a 12 V DC, max 1.8 A power source.
• The included power adaptor delivers 12 V DC, max 2 A, 24 W.
5
• Bulb: 150 LEDs with a 460–620 nm wavelength range.
• Size: length 5 m, width 12.5 mm, height 4 mm. A certain
amount of deviation in size can be present due to
the glue's elasticity and the silicone housing.
• Remote control battery 1 × CR2025, 3 V.