GLASS glam Installationsanleitung Seite 10

EN
• Read the manual carefully in all its parts before using the
product.
• Keep this manual for further consultation.
• The manual is intended for different models and versions, so
the product may look different from the manual illustrations.
However the instructions remain unchanged.
• The company reserves the right to make any changes
considered suitable without notice or replacement.
• This product is intended only for the use for which it has been
designed. The manufacturer is not responsible for any damage
caused by improper useage.
• The product identification data (model, power, voltage,
manufacturer's name) are contained in the silver data plate
on the unit and on the warranty card. It is issued at the time
of testing.
• Make sure that the drain is always efficient.
• Ensure that the floor around the product is always dry and
clean, to avoid slips or falls entering or editing the product
itself.
• It is not advisable to use the shower cabin with water that is too
hot. Use water with a maximum temperature of 38°C.
• This product is not intended to be used by persons (including
children) with reduced physical, sensory or mental capabilities
or lack of experience or knowledge, unless they have been
given appropriate supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• WARNING: children may use the product unsupervised only
when its operation has been clearly explained to them and
they are able to use it safely while recognising the dangers
of misuse.
all measurements are in mm.
PRE-INSTallaTION REQUIREmENTS
To prevent damaging the mixer parts, place a filter upstream of
the mixer.
TECHNICal INFORmaTION:
• Minimum flow pressure:
• Operating pressure:
• Recommended operating pressure:
• Hot water temperature:
The product's supporting structure is metallic. An efficient
ground system is therefore required, with sensitivity meeting
the relevant standards.
gROUNDWIRE.
The ground wire must be connected and fixed permanently
to the electrical system.
EQUIPOTENTIal CONNECTION.
The equipment must be connected to the equipotential
system of the room and duly fastened to its terminal to be
found in the product.
ROUTINE aND
SPECIal maINTENaNCE
Use water up to a maximum of 60°C to maintain the shine of the
product over the years.
Use soft cloths and neutral non- abrasive liquid detergents
for cleaning. Do not use cloths with synthetic fibres, abrasive
sponges, metal pads, solid and liquid detergents containing
abrasive substances, alcohol, acids for domestic use, acetone
or other solvents that can damage the surface.
SURFaCES IN HaRDlITE
To clean, first rinse the surface with warm water and dry with a
soft cloth. Then use a damp cloth to apply a light abrasive cream,
rubbing gently in a circular motion.
a
void
– the build-up of scale by cleaning periodically.
If there is a build-up of scale, use a non-abrasive sponge
(provided) and a normal domestic cleaning product to rub on
the scale.
After cleaning, rinse several times with warm water and dry with
a soft cloth.
WaRNINg!
Lemon juice recommended for removing heavy build-up of scale
on other surfaces, e.g. taps and fittings, could stain the surface in
HardLite. In this case use a non-abrasive sponge (provided) and
bleach to rub the stain. Rinse thoroughly with plenty of warm
water to remove all traces of bleach, which could otherwise
take the colour out of the surface. Dry with a soft cloth.
In the event of abnormalities run the following checklist.
all hydraulic connection checkup must be performed by a
hydraulic installation technician.
150 kPa (1,5 bar)
350 kPa (max 3,5 bar)
If the water is slow to drain away, check that the drain is not
250 kPa (2,5 bar)
blocked.
max 60°C
If the vertical whirlpool does not work, check that:
- There is water in the main pipe.
- The diverter is correctly set.
- There are no impurity into the pipes that prevent normal
If the above operations do not solve the problem, contact your
nearest service centre or the company.
10
HARDLITE
:
TROUBlESHOOTINg
water flow.