PEUGEOT ENERGYDrill-13LA Handbuch Seite 6

Assembly
WARNING! Never connect the plug to power
source outlet until all installations and adjustments
are completed and you have read and understood
the safety and operational instructions.
Note: The loose parts can be found in the pulley cover.
INSTALLING THE COLUMN TO BASE (Fig. 2)
1. Position the base (1) on the floor.
2. Place the column (2) on the base, aligning the holes
in the column support with the holes in the base.
3. Locate the three long hex bolts (3) from the loose
parts bag.
4. Place a bolt in each hole through the column
support and the base. Tighten with an adjustable
wrench.
INSTALLING THE TABLE TO COLUMN (Fig. 3~4)
1. Insert the table lock handle (1) into the hole (2) at
the rear of the table assembly. (Fig. 3)
2. Slide the table assembly onto the column. Tighten
the table lock handle (1) to lock the table assembly
to the column. (Fig. 4)
INSTALLING THE HEAD TO THE COLUMN (Fig. 5)
1. Carefully lift the head (1) above the column (2) and
slide it onto the column. Make sure the head slides
down over the column as far as possible. Align the
head with the base.
2. Using the hex wrench, tighten the two head lock set
screws (3) on the right side of the head.
INSTALLING FEED HANDLES (Fig. 6)
1. Screw the feed handles (1) into the right or left of
threaded holes (2) in the hub (3) and tighten.
INSTALLING THE CHUCK (FIG. 7)
1. Clean out the tapered hole in the chuck (1) and
clean the spindle (2) nose with a clean cloth before
pushing up the chuck onto the spindle nose.
2. Turn the chuck sleeve anticlockwise (when viewed
from above) and open the jaws in the chuck
completely.
3. Place a block of wood under the spindle, tapping
the wood with a hammer, or tap the chuck with a
rubber mallet or plastic-tipped hammer to properly
seat the chuck. DO NOT tap the chuck with a metal
hammer.
INSTALLING THE CHUCK GUARD ASSEMBLY
1. Put the nut (5) into the chuck guard hole (6).
2. Make the bolt (8) go through hole (7), bracket (10)
and hole (6) and then tighten.
(Fig. 8)
3. Secure the bracket (10) with the two screw (11)
onto the laser assembly (13) and then tighten.
4. Tighten the lock knob (12) into the bracket (11) to
adjust position of the chuck guard.
INSTALLING BATTERY FOR LASER GUIDE
1. Open the cover of the battery box.
2. Install 2 pieces of 1.5V 3A batteries into the battery
box.
3. Replace the cover.
4. Turn on the switch to check the LASER GUIDE.
Note: Replace the batteries with batteries that have
a rating of 1.5 volts (Number 4 series and AAA size
or equivalent). When replacing the batteries, the
battery guide should be thoroughly cleaned. Use a soft
paintbrush or similar device, to remove all dust and
debris.
THE LASER GUIDE
Your tool is equipped with our latest innovation, a
battery powered device using Class 1M laser beams.
The laser beams will enable you to preview the drill bit
path on the workpiece to be drilled before you begin
your operation.
WARNING:
AVOID DIRECT EYE CONTACT
A Laser light is radiated when the laser guide is turned
on. Avoid direct eye contact. Always turn off the laser
and un-plug the drill press from the power source
before making any adjustments.
A laser pointer is not a toy and should not come into
●
hands of children. Misuse of this appliance can lead
to irreparable eye injuries.
Any adjustment to increase the laser power is
●
forbidden.
When using the laser pointer, do not point the laser
●
beam towards people and /or reflecting surfaces.
Even a laser beam of lower intensity may cause
eye damage. Therefore, do not look directly into the
laser beam.
If the laser pointer is stored for more than three
●
months without use, please remove the batteries to
avoid damage from possibly leaking batteries.
The laser pointer includes no servicing components.
●
Never open the housing for repair or adjustments.
When the laser point has to be repaired, it should
●
be carried out to the laser manufacturer or an
authorized agent.
Laser Warning Label: Laser radiation do not view
●
directly with optical instruments class 1M laser
product <0.39mW, 400-700nm, CW, Acc.IEC
60825-1:2007.
4
(Fig. 20)