Werbung
Verfügbare Sprachen
Verfügbare Sprachen
switching-ON by means of the ON/OFF key all displays show
„0", the display dots are blinking and the control is ready for
cooking. If a cooking zone is "hot" , "H" will be displayed
instead of the static „0".
Multi-circuit cut-off
Depending on the design it is possible to operate dual- or
triple-circuit radiant heating elements with the LITE-Touch
Control.
When a multi-circuit heating element is put into operation,
all heating circuits are switched-ON at the same time. If only
the inner heating circuits should be used, the outer heating
circuit can be switched-OFF by means of the multi-circuit
key or in individual steps.
By operating the multi-circuit key the respective outer circuit
of the assigned active cooking zone (setting π „0") can be
cutoff anytime. An activated outer circuit will be indicated by
an additional LED. A renewed operation of the multi-circuit
key will add the outer circuit(s) at any time, the assigned
LED´s glow again (toggle-function)
If a cooking zone other than the one with multi-circuit
function will be selected, the multicircuit status will be
changed and all cooking zones will be deselected (the
decimal point extinguishes).
Behaviour of dual-circuit cut-OFF:
If the heating element to be controlled is a triple-circuit
heating element, the course of action is as follows:
· The first activation of the multi-circuit key cuts-off the outer
heating circuit and the top LED extinguishes.
· A second activation of the multi-circuit-key cuts-off the
middle heating circuit. (also the bottom LED extinguishes.)
· A third activation adds the middle heating circuit again. A
further activation adds the third heating circuit as well and
the assigned LEDs glow again.
Audible signal (buzzer)
While the control is in operation the following activities will
be signaled by means of a buzzer:
· normal key activation with a short sound signal.
· continuous operation of keys over a longer period of time
(_10 seconds ) with a longer, intermittent sound signal.
Timer function (optional)
The timer function is realized in two versions:
· Stand-alone timer 1..99 min: sound signal when the time is
over (= minute minder). This function is only available when
the cooktop is not in operation, i.e. when there is no
cooking.
· Cooking zone timer 1..99 min: sound signal when the time
is over, four cooking zones can be programmed
independently.
Timer as minute minder (stand-alone):
· If the control is OFF the standalone- timer can be operated
by activating the timer key. The timer display shows "00".
Operation of the Power-key puts the control back into the
stand-by mode and the stand-alone-timer will be cut-off.
· Adjustment range (0-99min), it can be set in 1-minute
steps with any key, starting at 1 up to 99 (end stop) with the
minus-key starting at 99 down to 0 (end stop)
· Continuous activation of the plusor minus-key results in a
dynamic increase of the adjustment speed up to maximum
value without sound signal.
· when the plus- or minus key is released in the meantime,
the adjustment speed starts again from a (low) initial value.
· adjustment can be made with a continously activated plus-
or minus-key or by tip-operation (with sound signal) After
the timer is set the time runs down according to the
adjustment. When the time is over there is a sound signal
and the timer display blinks.
The sound signal will be stopped
· automatically after 2 minutes and/or
· by operating any key. Then the blinking of the timer display
stops and the display extinguishes.
Switching-OFF/changing the timer
· The timer can be changed or switched-off anytime by
operating the TIMER- or MINUS key (with sound signal). The
timer will be switched off by counting down to "0" with the
minus-key or by operating the TIMER- and MINUS-key
together, which sets the timer directly to "0". For 6 seconds
the timer display remains at "0" before it will be switched-
off.
· If the control will be switched- ON by means of the Power-
key, the stand-alone timer will be switched-off also.
Timer programming on cooking zones
When the control is switched- ON an independent timer can
be programmed for every cooking zone.
· By selecting a cooking zone with the cooking-zone-
selectkey, then selecting the setting and finally activating the
timerselect- key, the timer can be programmed as a switch-
off function for a cooking zone. Around the timer four LEDs
are arranged. These indicate for which cooking zone the
timer has been activated.
· As soon as the timer has been selected, the assigned timer-
LED blinks and the dot in the timer display glows. If a
cooking-zone-select-key will be operated, the dot in the
timer displays extinguishes and the LED does not blink any
longer.
· When switching-over from one cooking zone to another,
the timer display always shows the present timer value of
the respective cooking zone. However, the programmed
timers of other cooking zones remain active.
· The further setting behaviour corresponds to the
STANDALONE- TIMER. For increasing the adjusted time, the
PLUS-key of the respective cooking zone has to be used.
(setting π "0")
· When the timer has run down, there is a sound signal and
the timer display shows "00" statically, the assigned cooking
zone timer LED blinks. The programmed cooking zone will
be cut off and „H" will be displayed if the coking zone is hot,
otherwise a stroke will show in the cooking zone display.
The sound signal and the blinking of the timer LED will be
stopped
· automatically after 2 minutes
· by operating any key.
The timer display extinguishes.
· The basic behavior follows the description of the "minute
minder" (stand-alone-timer).
Precautions (Fig. 3)
Werbung
