Herunterladen Inhalt Inhalt Diese Seite drucken

Stiga PARK 100 COMBI 3 Gebrauchsanweisung Seite 28

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 21
EN
• Use sharp blades.
• Keep the underside of the cutting deck clean.
4.4 COMPOSTING/REAR EJECTION
The deck can cut grass in two ways:
• Compost the grass into the lawn.
• Eject the grass behind the deck.
The deck is set for composting on delivery. In or-
der to eject the grass behind the deck, the plug in
fig. 12 must be removed.
Set the deck in cleaning or service position in order
to remove/install the plug.
5 MAINTENANCE
5.1 PREPARATION
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable from the spark plug and remov-
ing the ignition key.
5.2 WASHING POSITION
1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the highest cutting height.
4. Detach the rear section of the deck on the right
and left-hand side as follows:
A. Lift up the left-hand rear section of the deck
slightly to reduce the load from the cotter pin.
B. Remove pins and washer. See fig. 2.
C. Remove the right-hand cotter pin and washer in
the same way.
5. Grip the front edge of the deck and lift up. Hook
on the chain so that the deck is pointing diago-
nally upwards. See fig. 13.
It is absolutely forbidden to start the
engine when the deck is in the washing
position.
6. Lower the deck to the ground in reverse order
after the corrective actions have been carried
out. Reset the deck according to "3".
28
ENGLISH
5.3 SERVICE POSITION
5.3.1 Machines with fixed deck connections
1. Activate the parking brake.
2. Set the maximum cutting height.
3. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine.
See fig. 7.
4. See fig. 2. Detach the rear section of the deck on
the right and left-hand side as follows:
A. Lift up the left-hand rear section of the deck
slightly to reduce the load from the cotter pin.
B. Remove pins and washer.
C. Remove the right-hand cotter pin and washer in
the same way.
5. Release the belt tension as follows:
Park 2WD:
Remove the tensioner from the belt. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and remove the tensioner
with your right hand. See fig. 9.
6. Force the belt off the machines's pulley.
7. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the
rear edge on the ground. See fig. 14.
8. Lower the deck to the ground in reverse order
after the corrective actions have been carried
out. Reset the deck according to 3.1.
5.3.2 Machines with quick connections
1. Activate the parking brake.
2. Set the maximum cutting height.
3. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine.
See fig. 7.
4. See fig. 2. Detach the rear section of the deck on
the right and left-hand side as follows:
A. Lift up the left-hand rear section of the deck
slightly to reduce the load from the cotter pin.
B. Remove pins and washer.
C. Remove the right-hand cotter pin and washer in
the same way.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Release the belt tension as follows.
Park 2WD:
Remove the tensioner from the belt. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and remove the tensioner
with your right hand. See fig. 9.
Original instructions for use

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

110 combi pro125 combi pro

Inhaltsverzeichnis