Using The Machine - Stiga PARK 100 COMBI 3 Gebrauchsanweisung

6. Fit the belt on to the machine pulley.
7. Perform the cutting deck basic setting. See 3.4.
8. Tension the belt as follows.
Park 2WD:
Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig.9.
9. Suspend the unit in the implement lifter. See fig.
6.
10.If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 7.
3.2 MACHINES WITH QUICK CON-
NECTIONS
Example of quick connections, see fig. 8.
1. Place the deck in position in front of the ma-
chine.
2. Check that the quick connections are fitted to
the machine according to their supplied sepa-
rate instruction.
3. Check that the deck arms are screwed into place
in the quick connections. If this is not the case,
screw them into place. See fig. 8.
4. Set the maximum cutting height.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Fit the belt on to the machine pulley.
7. Tension the belt as follows.
Park 2WD:
Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig.9.
8. Set the quick connections in their front posi-
tions. See their supplied separate instruction..
9. Suspend the unit in the implement lifter. See fig.
6.
10.Perform the cutting deck basic setting. See 3.4.
11.If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 7.
3.3 TYRE PRESSURE
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
ENGLISH
3.4 BASIC SETTING
In order for the cutting deck to cut optimally, the
correct basic setting is required. The deck is in the
basic setting when its rear edge is 5 mm above its
front edge. This means that the deck is inclined
forwards.
Move the deck to the basic setting by lifting and
securing as follows.
On machines with 17" wheels: Install the washers
and the pins in the top hole. See fig. 17.
On machines with 16" wheels: Install the washers
and the pins in the middle hole. See fig. 18.

4 USING THE MACHINE

Check that the grass that is to be cut is
completely free of foreign objects such
as stones etc.
4.1 CUTTING HEIGHT
The best cutting results are achieved when the
when the top third of the grass is cut off. I.e. 2/3 of
the length of the grass remains. See fig. 11.
If the grass is long and has to be cut significantly,
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn
surface is uneven. This would entail a risk of the
blades being damaged against the surface and the
lawn's top layer of soil being removed.
4.2 INCLINE
The cutting deck's rear section can be lifted so that
the deck has a greater forward incline than that
provided by the basic setting. This incline affects
the cutting results as follows.
4.2.1 Basic setting
When the deck is in the basic setting, the best
"Multiclip" effect and good dispersion of the cut
grass are achieved. The basic setting is recom-
mended for normal grass. See 3.4.
4.2.2 Greater inclination
When the cutting deck is inclined forwards, the
"Multiclip" effect is reduced while the cut grass is
dispersed better.
Inclining forwards is recommended for thicker
grass.
Inclining forwards is recommended for thicker
grass.
4.3 MOWING ADVICE
In order to achieve optimum mowing results, fol-
low the advice below:
• Cut frequently.
• Run the engine at full throttle.
• The grass should be dry.
Original instructions for use
EN
27