The Remote Control System; Getting Started; Binding Process - Gm-Racing Xg-6I Bedienungsanleitung

Konformitätserklärung gemäß dem Gesetz über Funkanlagen und
Telekomunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE)
Declaration of Conformity in accordiance with the Radio and Telecomunikations Terminal Equipment
Act (FTEG) and Directive 1999/5/EG (R&TTE)
Graupner GmbH & Co. KG
Henriettenstraße 94-96
D-73230 Kirchheim/Teck
erklärt, dass das Produkt: Graupner XG-6i
declares that the product
Geräteklasse: 1
Equipment class
den grundlegenden Anforderungen des § 3 und den übrigen einschlägigen Bestimmungen des
FTEG (Artikel 3 der R&TTE) entspricht.
complies with the essential requirements of § 3 and the other relevant provisions of the FTEG (Article 3 of the
R&TTE Directive).
Angewendete harmonisierte Normen:
Harmonised standards applied
EN 60950:2006 Gesundheit und Sicherheit gemäß § 3 (1) 1. (Artikel 3 (1)a))
Health and safety requirements pursuant to § 3 (1) 1. (Article 3 (1) a))
EN 301 489-1 V1.8.1:2008 Schutzanforderungen in Bezug auf elektromagnetische
EN 301 489-3 V1.4.1:2002 Verträglichkeit § 3 (1) 2, Artikel 3 (1) b))
Protection requirement concernig electromagnetic compatibility
§ 3 (1) 2, Artikel 3 (1) b))
EN 300 440-1 V1.4.1:2008 Maßnahmen zur effizienten Nutzung des Frequenzspektrums
EN 300 440-2 V1.2.1:2008 § 3 (2) (Artikel 3 (2))
Measures for the efficient use of the radio frequency spectrum
§ 3 (2) (Article 3 (2))
0678
Kirchheim, 15. Januar 2009
Graupner GmbH & Co. KG Henriettenstraße 94-96 D-73230 Kirchheim/Teck Germany
Tel: 07021/722-0 Fax: 07021/722-188
17 94001 GM-Racing XG-6i Race Spec Instructions
94001-eng.indd Druckbogen 3 von 10 - Seiten (18, 3) 94001-eng.indd Druckbogen 3 von 10 - Seiten (18, 3)
Hans Graupner, Geschäftsführer
Hans Graupner, Managing Director
EMail: info@graupner.de

THE REMOTE CONTROL SYSTEM

Here you get an overview of the XG-6i Race Spec 2.4 Ghz 3-channel remote control system
and its various functions and settings. Before the fi rst trip should be sure all of these functions
and settings have read and understood.

GETTING STARTED

1. Place 8 AA batteries in the battery compartment in the bottom of the transmitter. Pay
attention to the polarity! If the batteries are loaded incorrectly, the transmitter may be
damaged.
When the transmitter will not be used for a longer period of time, always remove the
batteries.
2. Connect and install the receiver and servos.
Attention:
The transmitter comes with a Futaba charge socket for the use with Charging-Cord
No. 3022.65! Do not use any other Graupner charging cord, this may destroy the bat-
teries.
Be careful with the installation of the receiver. Never bend or shorten the coaxial
antenna wire! The actual „antenna" is the stripped end of the antenna wire and
must be installed in the vehicle so far above as possible. Avoid damages of the
antenna cable!

BINDING PROCESS

1. Press "ENTER" to see FUNCTION MENU
2. Use the +/- Keys to select the MODULATE function and press ENTER.
3. Use the +/- Keys to select YES .
4. Press ENTER to see SETTING...
5. Press EXIT to return to FUNCTION MENU, press EXIT again to return to the Main
Screen.
Atttention:
• Before setting ID Code, Please plug the bind plug into the fi rst channel of the
receiver and then turn on the receiver power, The receiver will come into the set ID
Code mode.
• When set ID Code is OK, the "SET OK " is displayed on the LCD. Otherwise
"SET ERR" will be displayed on the LCD.
During Frequency Pin Setup, please gather Tx and Rx as close as possible.
94001 GM-Racing XG-6i Race Spec Instructions
Bind-Plug
02
19.01.2009 08:02:45 19.01.2009 08:02:45