Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Quicklinks
Menu Guide
:
2:00
15
:
1:00-2:00
45
:30
1:30-2:30
The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage
supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system
impedance Zmax of 0.2 Ohms at the interface point of the user's supply. The user has to ensure that this device is connected only to a power
supply system which fulfills the requirement above. If necessary, the user can ask the public power supply company for the system impedance at
the interface point.
Part No.20037401
Revised 7/10
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
Complete Owner's Manual available online
A
C
DO NOT power spray
So...how do I use it?
Heating
1. Open oven door, place food in oven, and close oven door.
2. Turn time entry knob clockwise to desired time.
• Cooking time can be set up to 6 minutes.
• Oven begins operation and time counts down.
3. When cooking time has elapsed, microwave energy stops and oven
signal sounds.
Interrupting Operation
Open oven door to interrupt operation or turn time entry knob
counterclockwise to "0".
To resume microwave oven operation, close door and turn knob.
Changing Time and Canceling Mistakes
Heating time can be changed at any time while the oven is operating.
Turn knob to desired new setting. To set cooking time to zero, turn knob
counterclockwise to "0".
F
or full product documentation visit:
www.acpsolutions.com
Oven Wall Clearances
A—For North American (UL/CSA) models,
allow at least 3" (7.2 cm) of clearance
around top of oven. For International (50
Hz) models, allow at least 12" (30 cm) of
clearance around top of oven. Proper air flow
B
around oven cools electrical components.
With restricted air flow, oven may not
operate properly and life of electrical parts is
reduced.
B—Allow at least 3" (7.2 cm) between air
discharge on back of oven and back wall.
C—Allow at least 3" (7.2 cm) of clearance
around side of oven. One side of oven must
be open.
No metal pans
(Mechanical Dial)
2010 ACP , Inc.
Cedar Rapids, Iowa 52404
Werbung
Verwandte Anleitungen für ACP 20037401
Inhaltszusammenfassung für ACP 20037401
- Seite 1 If necessary, the user can ask the public power supply company for the system impedance at the interface point. or full product documentation visit: 2010 ACP , Inc. Part No.20037401 Revised 7/10 Cedar Rapids, Iowa 52404 www.acpsolutions.com...
- Seite 2 2010 ACP, Inc. No. de pieza 20037401 Cedar Rapids, Iowa 52404 www.acpsolutions.com...
- Seite 3 L’utilisateur doit s’assurer que cet appareil est branché à un système de source d’alimentation conforme aux exigences indiquées ci-dessus. Le cas échéant, l’utilisateur peut s’informer auprès du fournisseur public d’électricité pour connaître l’impédance du système au point d’interface. de pièce 20037401 our obtenir la documentation complète sur le produit visitez : ...
- Seite 4 Der Anwender muss sicherstellen, dass dieses Gerät nur an ein Stromversorgungssystem angeschlossen wird, das diese Anforderung erfüllt. Hierfür muss der Anwender ggf. das örtliche Stromversorgungsunternehmen bzgl. der Systemimpedanz am Anschlusspunkt konsultieren. omplette Produktdokumentation unter: Best.-Nr. 20037401 2010 ACP, Inc. Überarbeitet 7/10 www.acpsolutions.com Cedar Rapids, Iowa 52404...