Logic3 i-Station Bluetooth Benutzerhandbuch Seite 2

i-station Bluetooth (Bt010) – En user Manual
Thank you for purchasing the Logic3 i-Station Bluetooth. As with all Logic3 products it has been built
to the highest manufacturing standards and tested throughout its development, to ensure you get the
best possible product. Please read through and familiarize yourself with this manual before you use the
i-Station Bluetooth.
compatabile with a2DP Bluetooth devices
Functionality of the i-Station Bluetooth is dependent on the device the i-Station Bluetooth is paired with.
Devices with A2DP Bluetooth can use the i-Station Bluetooth to play music and receive calls. Devices
without A2DP cannot play music through the i-Station Bluetooth; it can only use the i-Station Bluetooth
as a Speaker phone. Other non Bluetooth devices can be connected using the supplied 3.5mm Stereo
Line-in cable. Further instructions on Bluetooth connectivity can be found in the user guide for your A2DP
Bluetooth device.
contents
i-Station Bluetooth USB Charge Cable
Product overview
ON/OFF
Power/Sync LED
Paring the i-station Bluetooth with a Bluetooth Device (First time connection)
1.
Ensure the i-Station Bluetooth is fully charged or that the i-Station Bluetooth is connected to a power
source.
2.
Turn the main power switch located at the back of the i-Station Bluetooth to the
ON position.
3.
Activate your Bluetooth device to the Searching mode (new device searching)
4.
Press and hold the 'Stand-by or Phone' button on the side of the i-Station Bluetooth until the Red/
Blue LED starts flashing on front of the i-Station Bluetooth. (i-Station Bluetooth will have 3minutes to
connect/pair with your Bluetooth).
or
Line in Cable
Answer/
Rejects
Standby
Calls
On/Off
Volume
Up
Line In
Previous/ Next/RW
FF Track Track
Mini USB Port
2
5.
'Logic3 BT010' will appear on your Bluetooth device.
6.
Select 'Logic3 BT010' and enter '0000' for the passcode if necessary.
7.
LED on front of the Speaker will stop flashing and a tone will sound to acknowledge successful paring.
8.
Check your Bluetooth device to ensure that conenction is successful.
Note: If after 3minutes no connection is made the speaker will sound and the LED will turn OFF.
operation of i-station Bluetooth
1.
Ensure the i-Station Bluetooth is fully charged or that the i-Station Bluetooth is connected to a power
source.
2.
Turn the main power switch located at the back of the i-Station Bluetooth to the
ON position.
3.
Press the 'Stand-by or Phone' button on the side of the i-Station Bluetooth until the Blue LED is ON.
4.
Turn on your Bluetooth device and select the connection 'Logic3 BT010'
5.
Once connected the following control functions can be used :-
Play Next song – Press
Play previous song – Press
Fast Forward – Press & Hold
Volume
Down
Rewind – Press & Hold
Volume Up/Down – Press either
Bluetooth device.
Switch the i-Station Bluetooth to Stand-by – Press and hold
operation of i-station Bluetooth as a speaker phone
1.
To answer a call – Press any key at the side of the i-Station Bluetooth.
2.
To Reject a call – Press & Hold
3.
To hang up a call – Press
4.
To switch a call between speaker and Mobile Phone – Press and Hold
of the i-Station Bluetooth.
5.
To Answer a call waiting (3rd Party) – Double Press
Bluetooth.
at the side of the i-Station Bluetooth.
at the side of the i-Station Bluetooth.
at the side of the i-Station Bluetooth.
at the side of the i-Station Bluetooth.
or press the volume controls on your
or until the Blue LED is OFF
or at the side of the i-Station Bluetooth.
or at the side of the i-Station Bluetooth.
or
or at the side of the i-Station
3
at the side